Xhorse Condor Date Reset when Turn on Power?

 Problem:

My old xhorse condor xc-mini key cutting date reset. The date is reset every time I turn on the power. It doesn’t come up right away. Any idea?

Solution:

Unscrew 3 screws marked red below, remove condor screen and shell.

The main board is on the left side, unscrew another 3 screws to take out main board

Find out battery CR1220, replace a new battery.
For example, the battery of condor mini plus (S/N KM02 and KM03) is on the right side of the board (shown image below)
Reinstall shell and screen after replace battery.

Go to System setting, set date to the current time. It should be fine.

www.vvdishop.com

Condor XC-Mini supports Xhorse App

Good News ! Now Xhorse CONDOR XC MINI & Condor XC-MINI PLUS can work on Xhorse App. Using same Dolphin database.

1. Support the Condor machine with the first 4 digits code of the serial number:
“KM03” and “KM05”

2. Users need to Upgrade the firmware and Xhorse App to latest version.
KM03 firmware version: 6.1.3
(App version 1.9.4)
KM05 firmware version 3.1.3
(App version 1.9.4)

How to make Condor Mini Plus work on Xhorse App?

Turn on Bluetooth connection on Condor

Run Xhorse App

Select device and auto search device

Bluetooth message received

Now you can use Condor mini on Xhorse app to cut keys

www.vvdishop.com

Condor XC-Mini Volvo HU56R Thickness problem solution

Q:

I just bought condor mini key cutter for one month, and already update to latest firmware, v2.1.1. Volvo HU56 thickness setting wrongly, it should be 2.5mm, and cutting thickness should be 1mm. volvo v40 key eats like 0.6 or more mm deeper than it should. it ate the clamp!!! and not very accurate.

A:

About Volvo HU56R condor machine database the key thickness is 3mm and cutting depth is 1.25mm
but if fact,users key is different, thickness is 2.5mm and cutting depth is 1mm.
so users can use define key data first ,named ‘HU56R-1_U’,later Xhorse will find a better solution.
1.connect PC to Condor machine
2.use attached software, sync’HU56R-1_U’ to condor xc-mini key cutting machine
3.select ‘cut by bitting’—enter ‘HU56R’ you will find HU56R-1_U,then cutting.

Note: Contact Xhorse engineer to get the define key data, skype: Xhorse-Support2.

Xhorse Condor Mini Series Number KM03 vs. KM02

This is for your information. It’s different between Xhorse Condor XC-Mini key cutting machine KM02xx and KM03xx series

What is the difference between KM02xx and KM03xx series ?

The difference is:
motherboard, driver board, touch screen and add a fan near power.
KM03xx supports Bluetooth function.

Btw, you can activate Bluetooth on Laptop/Tablet or Smartphone and press the “search for machine” button in Instacode and it will pair with Condor Mini.

How do you know your machine is KM02 or KM03?

Mate,turn on the machine you will find machine SN and software version in main-interface.

Where to get KM03 with Bluetooth?

Here you go. http://www.vvdishop.com/wholesale/xhorse-condor-xc-mini-plus-key-cutting-machine.html

Condor Mini KM03 test report:

Today tried to cut HU55P, cutter started to the other direction and cut into the jaw

I cut some HU64 and never had a problem with it.

100% hu64 is ok with condor xc007 and condor mini km03 tested by me many times…

I used it to cut HU100. Worked like a charm!!!

HU66, HU49, HU83 cutting OK.

Recently got the Condor Mini.

Seems good. However if the dust cover could have been designed a bit away from key it would’ve been nice.

I haven’t no any problems with Condor XC-Mini

cut keys blade HU64-3 without any problems

Just got a new km03 from vvdishop.com. So very new to this. Been very successful up till now. Tried to decode a Renault megane emergency key Card type. Renault-megane-2003- Condor checks the clamp position ok then goes looking for the tip of the key but misses the tip with the prob going down the middle of the cut for 5mm then backs off as it thinks no key is in the clamp. Is it operator error or a bug. Look like the probe is not low enough to bump into the key tip. Other than this I’m very happy.

Condor KM02 feedback:

I have machine with SN starting with KM02.

To cut keys HU92 BMW need to be in 1.00MM, when you select HU92 the device will ask you to chose between Land ravor and BMW, Land Rover came with 1.00mm and BMW with 1.25mm, if you try to cut with 1.25mm the key will not turn.

I have proved with 4 different machines and 3 different cars.

http://www.vvdishop.com/service/xhorse-condor-xc-mini-series-km03-vs-km02-9085.html

How to connect Condor XC-mini with laptop?

Question:

i have medium cutting speed, 2 passes on, maybe i should changed.

i tried today to use bluetooth with laptop instacode and condor xc-mini, but i cannot PAIR the device, i cannot find any bluetooth setting on xhorse condor, how do i connect? no info in user manual.

Solution from Xhorse expert:

You don’t need to do anything on condor mini. Activate Bluetooth on Laptop/Tablet or Smartphone and press the “search for machine” button in Insta-code and it will pair with Condor Mini.

www.vvdishop.com