ابزار Xhorse VVDI
Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزارابزار Xhorse VVDI
Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزارSolved) VVDI2 Program key on VW Transporter UDS System
If you have Xhorse VVDI2 VAG key programmer to add dealer key on VW Transporter/Caravelle T5 2011, but not work, you must read this post, the problem is finally solved.
Problem description:
VW Transporter/Caravelle T5 2011. Had an existing working key and used Xhorse VVDI2 to make a dealer key on a UDS cluster but something went wrong or more likely I did something wrong. It says 2-2 on the cluster and lights go off as if programmed but once cranked it starts and dies and the glow plug indicator light flashes. I stripped the cluster and tried with putting the cluster in to service mode but still much the same. With AD100 it says 2 keys coded and cluster in Mode 7. A friend came with his Zedfull and recoded in both keys and it said precoding ok but still the same issue. The dump of the original 24c64 and the backup I first made are attached and I’d appreciate any advice or help on this. Thanks everyone
folder: Transporter T5 24c64 Original Read
Folder: Transporter T5
Advice:
Config: This value contain car manufacture, key number, immobilizer status (new, learned, closed), keyless or not etc.
Your immo status is likely changed, did you press the reset immo button.
When did you made the 24c64 backups.
After entering service mode true obd, or after your keylearning procedure?
Question:
The initial backup (small file)was made before I made the key but I read the 24c64 only after it wouldn’t start. Any idea how to change the config from o7 to 06 again?
Instruction guide by senior:
go in to service mode by obd.
read immo data.
change the conf 7 in to 6.
press, write immo data.
press, reset instrument.
that should do it.
Finally! Solved
Thanks everyone. Yes it was me being stupid, I think I actually wrote the 24c64 complete file back instead of the smaller immo file. Did as advised and problem solved.
http://blog.vvdishop.com/solved-vvdi2-make-a-dealer-key-on-vw-transporter/
Xhorse VVDI Key Tool English Update to v2.3.8 2017.7.16
* * * * * * * * * * * * * *
Attention: This update only for North American or India English version(na,na-en,in,in-en). Other languages will be released on next week, please get Device Info to check language version.
This version must be updated with V2.3.8 and above. The upgrade may take about 30 minutes
1.transponder clone
+add chrysler 4D-64(4E) clone
+add toyota-G offline clone
+add hyundai ID-70 online clone(Use Calculate option in upgrade software)
+add ford ID-83 online clone(Use Calculate option in upgrade software)
+add ID-4A identify
2.generate transponder
+add toyota-G to generate special transponder
3.remote renew
+add more than 86 remote&keyless go prox unlock
4.remote prepare
*fixed XN serial keys problem on ID47 such as suzuki
5.add more vehicles data and fixed some bugs
mega link
VVDI2 BMW Version Key Programmer reviews
Xhorse VVDI2 BMW is BMW professional key programmer tool that covers full functions of BMW Multi Tool,and which is better than Multi Tool. Software and firmware both online upgrade-able.
VVDI2 BMW includes BMW OBD and CAS4 authorization, and VVDI2 BMW software language: English, Italian, Spanish, Dutch, Hungarian.
VVDI2 BMW can support not only key programming,but also km,some can do via OBD,some need CAS Plus,some need by eeprom way,like CAS4,needs to use VVDI Prog to read eeprom data,then use with VVDI2 BMW.
Xhorse VVDI2 BMW Key Programmer Feedback:
1) Cars that I have successfully done with VVDI2
2005 BMW E87 CAS3
2006 BMW E90 CAS3
2003 BMW E60 CAS2
2010 Audi A5 with Keyless Entry
2011 Audi A3
2009 VW Golf mk6
2) I tested my vvdi2 on 2008 bmw m6 today. It worked flawlessly and was a bit quicker than multi-tool.
3) I did a perfect job on 2010 bmw X5 with ISTAP today. I downgraded CAS ( I backed up eeprom with xprog first) and then retrieved key info OK. Adding key was a brieze after that. Cleared all errors, synchronized ELV. DONE
4) Hi i yesterday have bmw f10 2012 year ,read cas4+, change, write back all ok work .happy 100%
5) BMW cars I have completed with VVDI 2.
– EWS 2
– EWS 3
– EWS 3+
– EWS 4
– CAS 2
– CAS 3
– CAS 3++ (ISTAP)
I think some people need to do more research before blaming tools.
Credit to VVDI2 BMW users from DK forum.
http://blog.vvdishop.com/xhorse-vvdi2-bmw-key-programmer-feedback/
VVDI2 Reading Audi A6 / Q7 EEPROM from EZS
Here is the instruction showing the capabilities of the Xhorse VVDI2 VAG key programmer: Reading EEPROM with EZS Audi A6 / Q7
How to read eeprom from EZS AUDI by OBD with VVDI2:
Select Key Learn->4th immobilizer system- Audi-> A6L/Q7/Allroad
A6L/Q7/Allroad EZS-Kessy (J518) 4th immobilizer system
Select Auodetect from engine (ECU)
reading data, please wait
Reading data success
Read and save EZS-Kessy EEPROM (J518)
Start security login
Reading data…
Reading data success
Save eeprom
click on Read VIN
VVDI2 Read Audi VIN successfully.
VVDI Key Tool copy Mahindra Scorpio 2017 Remote key
Q:Can I use VVDI Key Tool to copy 2017 Mahindra Scorpio 3 button remote key 434MHz?
A: Yes. And it’s easy!
Follow steps below VVDI Key Tool clone a new Mahindra Scorpio remote, a 3 minute job!
Use VVDI Key Tool software V1.2.8 in this case:
Choose VVDI Key Tool “Remote Clone” function.
And choose “Special Clone”.
Put the original Mahindra Scorpio remote key close to VVDI Key Tool remote generator antenna area.
Follow the instruction:
First press the remote LOCK button for 2 times.
Next press the remote UNLOCK button for 2 times.
Then press the Trunk Release button for 2 times.
After that, press OK button to clone remote key.
Connect the new remote key PCB with VVDI Key Tool via the programming cable.
Set the remote key frequency as 434MHz then choose “Clone” to copy the new key.
VVDI Key Tool clone a new Mahindra Scorpio remote key 100% success.
Now insert the key battery and put the new key PCB back into the key shell.
And test the new key work totally same as the original one!
Xhorse VVDI Key Tool Remote Maker Mahindra Scorpio 2017 remote OK!
