Questions:
Q1: Can i make key VW Jetta 2020 and tiguan 2020 MQB49 5c with xhorse vvdi2?
Q2: How can I make key for Immo 5C with VVDI2, how to calculate?
Q3: How do i get immo data mqb49/5c on vvdi key tool plus?
Answer:
Add key:
If the key is MQB49 or 5C you can add key with vvdi2 or key tool plus.
You need proper immo data file and key. If xhorse cannot calculate data, need to get immo data from 3rd party.
If the key is mqb49 (5c), i.e VW Tiguan 2022, is currently not supported. Not possible now with immo data file. You cannot make key with xhorse devices.
Key needs to get from dealer and activate online with Odis.
All keys lost:
No, it cannot be done with xhorse devices.
Need key of dealer and then odis.
Also odis can not program after-market keys only OEM.
Problem:
I am having an issue with the xhorse mini key tool. I was updating it (firmware) via upgrade kit and the battery died. Now I keep getting fails trying to complete update and tool is stuck on ‘USB —PC’. It says SAFE1 also when I turn it on.
Solution:
Firmware upgrade should be done via Upgrade kit.
If key tool battery is low or the internet is unstable, you will fail to update firmware.
Charge keytool and change network, try several times.
If all failed, there is something wrong with the mini key tool. Send back to your dealer for repair.
Following I’m gonna show how to add a smart key for 2017 Nisscan Versa with Xhorse VVDI Key Tool Plus Pad by OBD. This is a working key and a new key. Before programming, you’ll have to read out the BCM codes.
Read BCM Code
Immo programming >> Asia >> Nissan >> Select from system >> Smart >> 4 digits PIN >> Type 5(no slot – button type) >> Start programming >> Read BCM code
Switch ignition on! Click “OK”.
Body computer number(BCM number) has been read out.
Use the “5-digit BCM code calculation password” function to get the password to match(This function requires online)!
Perform calculate of PIN codes by online?
Note:
Click “Yes”.
The BCM code and passwords were read out.
Just take a photo to record.
Program New Key
Program smart key >> Input password
Take all smart key out of the car and click the start button once, turn on the security light(double flash lights).
To match the smart card, the direction lock must be released first(the program is released)
Yes: Automatically release the direction lock and execute the matching function.
No: Directly execute the matching function(used when the direction lock has been released by the program).
Click “No”.
Please follow the step below to complete the matching operation:
After the matching is completed, verify the key as follows:
Open the door once, press the remote UNLOCK and LOCK button once, start the engine and wait for 5s.
Complete.
This is using VVDI Key Tool Plus to add 2017 Nisscan Versa key successfully.
Does xhorse vvdi bimtool pro support E series 8HP EGS?
No, there is no 8HP in E series in the menu.
VVDI BIMTool Pro supports BMW E series 6HP, F series 6HP and F series 8HP.
VVDI BIM Tool BMW EGS Function Introduction:
Read gearbox status: Support to read 8HP gearbox status, whether it is a new, etc
Diagram: OBD and gearbox connection diagram
Backup coding: Back up the code in the gearbox
Restore coding: Restore the code in the gearbox
Clear the F-Series 8HP Gearbox ISN: Clear the internal information that have used which have been matched and make them to new part
Reset F-8HP adaptation: Restore the adaptation information in the gearbox to the initial status
Reset F-6HP EWS: Restore the immo information in the gearbox to the initial status
Read E-6HP ISN (E70, E65 and E63): Read the ISN information from the gearbox, it is possible to get several ISN values, but only one is correct. The ISN you get is 4 bytes, the first 2 bytes are the gearbox ISN, and the last 2 bytes are the DME ISN. The gearbox byte is encrypted, and the DME byte is not encrypted. If the ISN read from DME is same as last 2 bytes ISN read from gearbox, it is the correct ISN
Reset E-6HP EWS: Restore the IMMO data in the gearbox to the initial status
Reset E-6HP adaptation: Restore the adaptation information in the gearbox to the initial state
How-to: program spare VW Caddy year 2018 MQB remote key using xhorse vvdi2 vag key programmer.
Here the customer wanted 3 remote spare keys (4 in total).
Tried ALL of Xhorse and Keydiy without success.
The remote didn’t work for anyone!!! That’s why an original was programmed.
In addition, have programmed 2 keys without remote using XT1M MQB chip. The customer had thus received his 4 keys. Unfortunately only 2 remote keys.
Step 1: Backup eeprom & immo data
Run VVDI2, Select Key Learn->MQB platform instrument immobilizer->Instrument with NEC+24C64 MQB key
Read EEPROM and save
Read IMMO data and save
Reset instrument to activate the instrument after all operation are finished.
Step 2. Remote Programming
Select Add key
You should backup EEPROM and Immo data before learn key.
Select Learn key, login with security code from immo data
Load immo data and input key number need to learn: 2
Insert the dealer key into car and switch on for at least 2 seconds.
Start learning key
Insert next key within 5s and switch on the ignition
Step 3. MQB48 transponder programming
using xhorse XT1M MQB48 transponders
Select immo data prepare key
update immo data to generate dealer key
Prepare normal dealer key
input new key (XT1M transponder) into vvdi2 programmer
Prepare dealer key success
Load immo data again to generate 2nd xt1m transponder
Prepare 3rd dealer key success
Insert xt1m chip into key shell.
Step 4. Transponsdr key programming
select Add key function
Select Learn key, login with the security code from immo data
Load immo data and input key number need to learn: 4
Insert the dealer key into car and switch on for at least 2 seconds.
Start learning key
Insert next key within 5s and switch on the ignition
repeat operation and learn all 4 keys until completed.
Test all keys.