Here is the instruction on adding a spare key to Audi Q3 VDO 2009+ by xhorse vvdi key tool plus.
Main steps:
Read immo data
Generate Dealer Key
Reset instrument
Learn Key
Step 1: Read Immo Data
Connect Key Tool Plus with OBD.
Turn ignition on, press
Immo programming >> Europe >> VW >> Automatically diagnose models >> Start programming
Detect instrument type VDO NEC 2009+ UDS
Select Read Immo data
Get the working key close to antenna
Switch on with working key before press OK. If car has keyless GO, put the working key nearby car coil and switch on.
Press “OK”.
Select “Login method 1”.
Save immo data
Reset instrument to activate dash after operation finished
Put original key into xhorse key tool plus coil
Select Generate dealer key-load immo data
Upload immo data read above
Select Prepare normal dealer key
Place an unlocked ID48 chip/key into the coil
Make dealer key success
Reset instrument
Select Key Learn function
You should backup EEPROM and immo data before learn key
Select programming method: Program keys, get the login code from immo data to log in.
Put original key into igniton switch
Input number of keys to be learnt: 2
Upload immo data saved before
Place 1st key into the car sensing coil and don’t remove.
Learn 1st key
Place the 2nd key close to the antenna and wait
Learn 2nd key success
Xhorse vvdi key tool plus release new license to read ISN from MSV80 MSV90 MSD80 MSD81 MSD85 MSD87 N20 N55 B38 ECUs/DMEs.
What’s required:
Xhorse Bosh ecu adapter XDNP30
KTP BMW ISN License
Here is an example on reading BMW MSD87 DME ISN on bench.
Select Immo Programming->BMW->Select from system->ECU ISN-> Bench read ISN-MSD90/MSV80 MSD80 MSD81 MSD85 MSD87 etc->MSD87
Check connection diagram and connect key tool plus with DME via XDNP30 adapter
Pin detection
Reading ISN
Read ISN success
Save ISN data.
Done.
www.vvdishop.com
This is a tutorial on how to read MQB dashboard data to add keys using Xhorse VVDI Key Tool Plus. Before using this feature, make sure you’ve activated Xhorse VAG MQB License and the IMMO database on Key Tool Plus has been upgraded to the latest version.
Preparation
Read VW MQB NEC35xx Data
Now we’ll need to read the chip data on the PCB board.
Immo programming >> VW >> Select by type >> MQB instrument immo system >> Instrument – MQB48(VDO/JCI-NEC35xx lock) >> Start programming
Before we read data, please read the disclaimer carefully, make sure you’ve fully understood and agreed with the contents and responsibilities.
OK >> OK
Programmer reads files >> Read NEC35xx chip
Check the wiring diagrams carefully and locate the one that is same to the dashboard MCU. Follow the on-screen instructions and finish the operation.
Lifting Pin from CPU Instructions
Apply some scaling power onto the pin we’ll lift later.
Now we’ve finished the pin lifting.
Then we follow the wiring diagram and solder the MCU cable. Connect VVDI Key Tool Plus with the module via DB15 cable.
Read >> Continue
The whole process is gonna take 3-5 minutes.
Reading successfully and now save the data.
The data can be used for generating dealer key or key learning.
MQB Key Adding
Generate dealer key-Load immo data >> Open immo data file we just saved >> VW >> Prepare normal dealer key >> OK >> Yes >> Add key – you should have a working key
Place the original working key into Key Tool Plus, press “OK”.
Next, just follow the general steps to add key.
Here is a guide to renew/virgin a second-hand engine computer for Mercedes W203 C270 CDI, before replacing the old one.
ECU type: BOSCH EDC15C6 CR2.
Device used to renew: Xhorse vvdi key tool plus
Procedure:
Connect vvdi key tool plus with EDC15C6 ECU. You need to find pinout by yourself.
Read ECU data
Save ori. ECU data
Select Renew function
Get erase password successfully
Renew ECU success.
Read ECU data again.
ECU is personalized and deactivated.
Here is the instruction to read VAG MQB 35XX locked immo data and program key with xhorse vvdi key tool plus. It is similar to vvdi2+ vvdi prog (check procedure). But vvdi key tool plus will read immo data and decode by itself.
Procedure:
Go to Immo programming->VW->Select by type-> Instrument-MQB48 (VDO/JCI-NEC35xx locked)-> Start programming
Then select Read Immo data->Use the programmer to read data directly
Check wiring diagram in tablet or check wiring here
Xhorse VVDI Prog V5.2.5 Adds VAG MQB48 NEC35XX
Here we use lift pin method.
Then read immo data and save.
NOTE: The saved immo data is still encrypted. So if you go to Generate Dealer Key-Load immo data, then upload this immo data, xhorse key tool plus will give error “The file is not supported by current model”
Go to Read Immo data->Load the read programmer file
Select and upload immo data read above
Calculating/decrypting immo data in progress
Read immo data successfully. Save immo data. Now you can generate dealer key and learn key with the immo data.
Select Generate dealer key-Load immo data
Upload immo data (the decrypted long file)
Check key information and press OK to continue generate dealer key, then learn key.
https://www.vvdishop.com/service/vvdi-key-tool-plus-read-vag-mqb-nec35xx-immo-data.html