Renew BMW PCF7953 Smart Key Comfort Access by VVDI Key Tool Max

 Here’s the tutorial on unlocking/renewing BMW smart key comfort access (non OEM) remote with xhorse vvdi key tool max remote maker.

OEM come sealed so you have to have aftermarket shell to replace OEM. Old shell is trash after cutting open!

BMW 2004-2010
Smart key/Comfort Access
FCC KR55WK49147
Aftermarket
Remote (None OEM)
Chip PCF7953

Status: already locked.

In key tool max, go to Special function- Remote Renew- BMW- 5WK49147 E series 315MHz Smart Key

You have two options to unlock smart key, by xhorse renew adapter or soldering
key tool max will show you wiring diagam

We don’t have renew adapter so we have to solder

A renew cable is required. You can make your own renew cable or buy additionally

Follow key tool max wiring to connect key board with renew adapter

Press UNLOCK

Renew smart key success

the smart remote has been unlocked successfuly

Install key shell. The smart key can be programmed to car with obd programmers.

www.vvdishop.com

Renew Dodge Fobik key with Xhorse VVDI Key Tool Max

 Today I’m gonna to use Xhorse VVDI Key Tool Max and the Renew Adapters Set just purchased to unlock an OEM Dodge Fobik key. Once it is unlocked, it’ll be able to learn to another car.

The Renew Adapters Full Set has 12 adapters, with this particular set you can do all kinds of vehicles. Instead of having to solder wires to the board, these adapters actually just line up the board where it needs to be and allows the Fobik to be unlocked.

How to unlock Dodge Fobik key?

Here is the OEM Dodge Fobik key.

The Key Tool Max and Renew Adapter No.10 are connected.

As you can see, the Fobik key is “Already locked”.

Open its outer shell, to put the circuit board properly in Renew Adapter.

Press on Xhorse Key Tool Max,

Special function >> Remote renew >> Chrysler & Jeep & Dodge >> Select correct FCC ID: IYZ-C01C M3N5W783X >> Unlock

Renew in process, wait until 100%…

Renew success.

Let’s get the key out to check info again.

As you can see, it is “Unlocked” now, and still outputting a signal.

All right, it’s all good done!

Renew Dodge Fobik key successfully via Xhorse Renew Adapter & VVDI Key Tool Max.

https://www.vvdishop.com/

How to Clone 2014 Fiat Doblo key with Xhorse Key Tool Max

 How to use Xhorse VVDI Key Tool Max to clone a spare key for 2014 Fiat Doblo? It’s very fast and easy, following I’ll show the procedure.

An original working key, a blank new key and a VVDI Super Chip are required.

Put the original key into Key Tool Max coil, press

Transponder clone >> Read transponder

Information has read out, it’s cloneable.

Just follow the instructions to clone, continue to press

Clone >> Start clone >> 46 transponder clone >> Original key clone(recommended)

Note: don’t remove the original key

It’s asking to sniff at the data, so what I have to do is to put the antenna near the ignition and turn it on.

Put the original key into Key Tool Max coil again as required.

Wait collecting data…

Calculate success.

Take out the original key, then put a Super Chip into coil.

Write data success.

Let’s put the Super Chip inside a new key shell to have a test.

As you can see, it starts the vehicle.

Let me try the original one, both can start the car.

It is a very simple process with VVDI Key Tool Max to clone a key for 2014 Fiat Doblo. It only takes me 4 minutes to finish.

https://www.vvdishop.com/

How to Add M3 2011 CAS3+ Key with Xhorse Key Tool Max

 How-to: BMW M3 2011 CAS3+ ISTAP 0L15Y spare key programming with xhorse mini prog and key tool max.

1.Read EEPROM with VVDI Mini Prog

Remove CAS3+ Module

Connect mini prog CAS3 solder free adapter with CAS3 module

Follow mini prog app prompts to read EEPROM and save data

2.Make dealer key with xhorse vvdi key tool max 

In key tool max app, select Special function -Immo data tool- BMW- CAS3+ 0L15Y

Then load eeprom read by the mini prog

Write key with dump

Reinstall CAS3+ module.

Test new key and remote control.

Done.

www.vvdishop.com

Generate 40 bit 4D Ford with Xhorse Key Tool Max

Here is the using tips of xhorse vvdi key tool max on generating 40 bit 4d ford transponder key.

Use super chip and generate the chip by selecting the option for the chip (New 4D chip (40 bits)).

Ford 80 bit chips are backwards compatible with the 40 bit keys. Just stock the 80 bit and you good to go.

Don’t delete keys as you can only use 1 super chip and need 2 keys minimum to program in or car won’t start.

Just add key, don’t do akl (all keys lost), you can add 1 key without another key by selecting add key instead of AKL.