ابزار Xhorse VVDI
Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزارابزار Xhorse VVDI
Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزارXhorse VVDI2 Golf 5 K-line upload data failed solution
Problem:
Hi, I have with Xhorse vvdi2 vag v5.5.0 problems with edc16u1 ecu and dashboard.
It can’t read golf 5 2005 year. Something not ok with it
It looks like K line not working.
It can’t read golf 5 2005 year. Something not ok with it
It looks like K line not working.
picture attached:
Error “Can’t connect to device. Switch ignition OFF/ON and retry”
Error “Non-standard upload data failed”
Solved!!!
Here’s the customer solution:
I test it this morning and all works fine now.
I removed soldering ball and i reinstall drivers and all working fine.
I removed soldering ball and i reinstall drivers and all working fine.
It reads now over kline it detects edc16 ecus and it read immo data eeprom and also dashboard it can read now.
I check k line from vvdi2 db25 connector on PCB to the optocupler (relay) omron, and from it to the ADG1606B multiplexer then from multiplexer to the L9637 interface. Then from it to the mcu Rx and TX line. All is ok. Even replace from vvdi 1 L9637 ISO 9141 interface. Didn’t work. Then I measured supply to the omron optocoupler relay it has 1.2 v when activate Kline communication. Check also 120ohm pull down resistors, check supply to the multiplexer ADG1606B it is ok 3.3v ako also on iso 9141(L9637) interface, and also I have on oscilloscope TX and TX signals from mcu to the L9637 it send data when It activate Kline. And in the end I found one solder ball between legs of multiplexer. You can see it on picture that I send you before. First time i open it. That was the main problem and USB drivers.
this is all i tested on this interface. Now all is fine and i can work now![<div class=]()
vvdi2
vvdi2 vag
I check k line from vvdi2 db25 connector on PCB to the optocupler (relay) omron, and from it to the ADG1606B multiplexer then from multiplexer to the L9637 interface. Then from it to the mcu Rx and TX line. All is ok. Even replace from vvdi 1 L9637 ISO 9141 interface. Didn’t work. Then I measured supply to the omron optocoupler relay it has 1.2 v when activate Kline communication. Check also 120ohm pull down resistors, check supply to the multiplexer ADG1606B it is ok 3.3v ako also on iso 9141(L9637) interface, and also I have on oscilloscope TX and TX signals from mcu to the L9637 it send data when It activate Kline. And in the end I found one solder ball between legs of multiplexer. You can see it on picture that I send you before. First time i open it. That was the main problem and USB drivers.
this is all i tested on this interface. Now all is fine and i can work now
Program Seat Leon MQB Smart Remote Key by VVDI2
A Spanish VVDI2 VAG user has successfully programmed a remote smart key on a Seat LEON MQB system. Here’s some operation steps provided.
At this moment, VVDI2 MQB key is not available yet, so he used 5G0959752BC from ali (Works for all the cars, VW Polo need to use 5G0959752BB.)
Open VVDI2 VAG software
Select Key Learn->MQB platform instrument immobilizer->Instrument with NEC35xx (Continental/VDO)
Click on Diag to load vehicle information
Read EEPROM/FLASH data and save
Turn ignition on with the original key
Follow these steps to program key:
1. The instrument box is off while you are reading these instructions. You need to reset instrument after completing the process
2.Read EEPROM and save
3. Read immo data and save them.
4. Dedicate key to the vehicle (you can go to step 7 if you have a working key and also do not want to add keys)
5. Reset instrument box
6. Add key. use the immo data to program the new key
7. Finish process
2.Read EEPROM and save
3. Read immo data and save them.
4. Dedicate key to the vehicle (you can go to step 7 if you have a working key and also do not want to add keys)
5. Reset instrument box
6. Add key. use the immo data to program the new key
7. Finish process
VVDI2 Read Immo data and save it
Reset “instrument box” to activate the box after finishing the process
Make Dealer Key
Select brand: Seat
in this case we will use the second option
in this case we will use the second option
Attention: If you have the dedicated key in a normal way it will not support coding ONLINE or changes in the immobilizer of the following units:
01-Engine
02-Gearbox
17-Instruments
9-CAN Gateway
28-Electrical Steering Column Lock
We recommend selecting the OEM option, which has the same ID as the original keys, will support the
ONLINE operations.
We recommend selecting the OEM option, which has the same ID as the original keys, will support the
ONLINE operations.
Are you sure to make a normal Seat key?
If you are sure you have selected the correct brand press “YES” to continue, if you do not press “NO”
If you are sure you have selected the correct brand press “YES” to continue, if you do not press “NO”
Place the new key into the VVDI2 antenna and press OK
Make key success. Please program the new key to the vehicle.
Use “Reset instrument” to reset the box after all operations
Attention: You must make a backup of the eeprom before programming keys.
If you have a security copy you can continue, if you have not copied before immo data, press NO
Select second option to learn key. login with security code from car. Put the key into ignition switch on accord flowing tips. You must prepare all the working key. If the key not learned, it can not start the engine after learned.
Inter leaning key number: 2
2 keys should all be learned
Key learn success.
Test the remote control and start vehicle with the new key.
Working.
Program Seat Leon MQB Smart Remote Key by VVDI2
A Spanish VVDI2 VAG user has successfully programmed a remote smart key on a Seat LEON MQB system. Here’s some operation steps provided.
At this moment, VVDI2 MQB key is not available yet, so he used 5G0959752BC from ali (Works for all the cars, VW Polo need to use 5G0959752BB.)
Open VVDI2 VAG software
Select Key Learn->MQB platform instrument immobilizer->Instrument with NEC35xx (Continental/VDO)
Click on Diag to load vehicle information
Read EEPROM/FLASH data and save
Turn ignition on with the original key
Follow these steps to program key:
1. The instrument box is off while you are reading these instructions. You need to reset instrument after completing the process
2.Read EEPROM and save
3. Read immo data and save them.
4. Dedicate key to the vehicle (you can go to step 7 if you have a working key and also do not want to add keys)
5. Reset instrument box
6. Add key. use the immo data to program the new key
7. Finish process
2.Read EEPROM and save
3. Read immo data and save them.
4. Dedicate key to the vehicle (you can go to step 7 if you have a working key and also do not want to add keys)
5. Reset instrument box
6. Add key. use the immo data to program the new key
7. Finish process
VVDI2 Read Immo data and save it
Reset “instrument box” to activate the box after finishing the process
Make Dealer Key
Select brand: Seat
in this case we will use the second option
in this case we will use the second option
Attention: If you have the dedicated key in a normal way it will not support coding ONLINE or changes in the immobilizer of the following units:
01-Engine
02-Gearbox
17-Instruments
9-CAN Gateway
28-Electrical Steering Column Lock
We recommend selecting the OEM option, which has the same ID as the original keys, will support the
ONLINE operations.
We recommend selecting the OEM option, which has the same ID as the original keys, will support the
ONLINE operations.
Are you sure to make a normal Seat key?
If you are sure you have selected the correct brand press “YES” to continue, if you do not press “NO”
If you are sure you have selected the correct brand press “YES” to continue, if you do not press “NO”
Place the new key into the VVDI2 antenna and press OK
Make key success. Please program the new key to the vehicle.
Use “Reset instrument” to reset the box after all operations
Attention: You must make a backup of the eeprom before programming keys.
If you have a security copy you can continue, if you have not copied before immo data, press NO
Select second option to learn key. login with security code from car. Put the key into ignition switch on accord flowing tips. You must prepare all the working key. If the key not learned, it can not start the engine after learned.
Inter leaning key number: 2
2 keys should all be learned
Key learn success.
Test the remote control and start vehicle with the new key.
Working.
How to change Seat Leon III MQB mileage with VVDI2
New test feedback: done Seat Leon 3 / Golf 7 MQB mileage correction with Xhorse VVDI2 VAG 5.2.1 success.
Open VVDI2 software
Select Seat->Key Learn->Immobilizer of instrument platform MQB-> instrument with NEC+24C64 MQB key
Click read data, auto detect vehicle type etc
Click on Read KM
Current mileage: 500KM
check odometer on instrument, it is the same
Enter the mileage you desired:118090KM
Click on Write KM
Accept VVDI2 warning messages
The dashboard indicators go off during the procedure, it is normal.
Success.
VVDI2 Seat Leon 3 MQB odometer correction is done.
Xhorse VVDI2 V5.0.0 software adds VAG MQB system
Xhorse VVDI2 key programmer latest software version V5.0.0 updated on Jan, 6th, 2018.
2018-01-06 ***
Require firmware V5.0.0
************************************************
!!! Update V5.0.0 firmware require use “Upgrade Kit“, you can find it from VVDI2 Quick Start from V5.0.0 software !!!
===== VVDI2 VAG V5.0.0 =====
1. Add support for MQB NEC35xx immoblizer/KM function,
support following cars:
Audi A3/S3 2014+ Audi Q2
VW Golf7
VW Polo(MQB)
VW Tiguan II
VW Touran II
VW crafter 2017+
VW Passat B8 without virtual cockpit
Skoda Octavia III 2014.07+
Skoda Rapid 2015.06+
Skoda Kodiaq
Skoda Superb III
Seat Ibiza/Ateca/Toledo 2015.06+
Attention 1: This type only support cars with cluster Continental/VDO. JCI type and virtual cockpit was not included
2: MQB Immobilizer function require MQB key made by VVDI2.
2 Bugfix
===== BMW V5.0.0 =====
1. Improvement for read ECU ISN
2. Bugfix
===== Porsche V5.0.0 =====
1. Bugfix
===== PSA V5.0.0 =====
1. Bugfix
===== Transponder Programmer V5.0.0 =====
1. Bugfix
===== J2534 V5.0.0 =====
1. Bugfix
===== Online Upate Tool V5.0.0 =====
1. Bugfix
===== Quick Start V5.0.0=====
1. Add “Upgrade Kit”
2. Bugfix
Free Download VVDI2 V5.0.0 software
https://mega.nz/#!O8JznCBZ!ZkbVpRZYa0ZxzuZjg6OG961KUZkDt7EEMEuSA0Xzkuw
http://www.vvdishop.com/info/xhorse-vvdi2-software-update-to-v500-2018-01-06-20219.html