برچسب condor dolphin - ابزار Xhorse VVDI

How to use Xhorse Dolphin XP005 to cut key by biting?

How to use Xhorse Condor Dolphin XP005 to cut key by biting?

Two ways of using the key bitting to make a key:

Method 1 :

Making a key without the original key.

1.Use some special tool to get the key bitting.

2.Break down the lock to read the key bitting on each metal of lock.

1) Click on “Cut by biting” on the main page
2) Select a key blank type
3) Select the ket type
4) Fix the key according to the picture show, select proper side of clamp and fix the key in correct position.
Put in the key bitting and check all the information before you click on “Cutting key” for make new key.

Method 2:

Making a key with the original key.

1) Click on “Cut by biting” and select a key blank type
2) Select the key type
3) Click on “Decode key” to duplicate key biting
4) Click on “Cutting Key”

www.vvdishop.com

condor dolphin condor dolphin xp005

Emily پنج‌شنبه 7 شهریور 1398 ساعت 12:20

0 نظر

How to use Xhorse Dolphin XP007 to cut keys?

Xhorse Dolphin XP007 manual key cutting machine is tested ok to cut Sided, Track, Dimple and Tibbe keys. It is very suitable for outdoor key cutting jobs.

Xhorse Dolphin XP007 has unique clamps.

It can clip both the civilian keys and car keys (i.e Ford, Benz keys)

2.The two sides of clam can be switched, and the other side can clip the cylinder key too.

There are two screws bellow and one screw on the side. If you find the whole clamp has deviation or the key cutting job has deviation, just loose the screws and calibrate.

Xhorse Dolphin XP007 VS Dolphin XP005 VS Condor XC-002

Compared with the Dolphin XP-005 automatically key cutting machine , Dolphin XP007 is manual, therefore, it is cheaper; also It does not depend on the mobile phone, so it is convenient to use anywhere anytime.

Dolphin XP007 can cut as the same key types as Condor XC-002 manual key cutting machine.

XP007 is lighter (about 30.86lb), portable and comes with battery, so it is portable to take out for key cutting job.

Xhorse Dolphin XP007 workable car key type.

Xhorse Condor Dolphin XP007 test reports

How does Xhorse Dolphin XP007 cut the flat key?

Clip the original car key on the right fixture, and the key blade on the left fixture.

There are several special clamp head for flat key.

Adjust the height

Start to cut.

Cut complete and insert it into the key lock to see if it can start the car.

Video demo:

How to cut flat milling key with Condor Dolphin XP007

How does Xhorse Dolphin XP007 cut single-sided outer key?

The original key won’t be clipped tightly on the fixture, please loose the front screw and turn the bottom of the clamp to the top, then clip the key on the fixture, you will find it will be tightly clipped.

Then tightly clip a key blade on the left side of fixture.

Adjust the machine height.

Cutting.

The key is cut flatly.

How does Xhorse Dolphin XP007 cut civilian key?

Clip the original civilian key into the first track on the right clamp.

Clip the key blade into the left clamp.

Adjust the machine height, when the height is ok, the upper first two indicators will flash.

Cutting……

Test successfully.

Xhorse Dolphin XP007 manual key cutting machine in stock

http://www.vvdishop.com/wholesale/xhorse-condor-dolphin-xp007-key-cutting-machine.html

condor dolphin dolphin xp007

Emily سه‌شنبه 1 مرداد 1398 ساعت 14:24

0 نظر

SEC-E9 vs. Condor Dolphin which is better?

The answer to the question depends on your needs , forget for now cheap or expensive , and look at what you need it for ;
Before deciding to buy xhorse Dolphin or sec-e9, please ask yourself these questions:
are you looking to cut occasional keys , a lot of keys ?

do you want updates and latest keyways first ?

do you want a machine for now or a machine for many years ?

do you want a machine that holds its value so you get a decent rate when you sell on rather than a worthless bit of kit , decide what you want and what coverage you want reliably then fit the right machine to your needs

HERE is the biggest factor you will want to look at right now

copies most type of key

kukai sec-e9/9z YES

xc-mini/dolphin YES

cuts car keys

kukai sec-e9/9z YES

xc-mini/dolphin YES

cuts house keys by code

kukai sec-e9 YES

xc-mini/dolphin NO cannot…….

can do engraving

kukai sec-e9/9z YES

xc-mini/dolphin NO

work with your phone

kukai sec-e9: No

Xhorse dolphin: YES

Has option for battery

kukai sec- E9/E9z: No

Xhorse dolphin: YES

Dolphin is half price than E9 and do much less than kukai sec- E9

can cut dimple keys (xhorse cant do)

can cut tubular keys (xhorse cant do)

can cut house keys(xhorse cant do)

can cut old GM 6 cut single side key(xhorse cant do)

can cut cabinet key y11 to code (xhorse cant do)

can engrave key with phone/logo whatever(xhorse cant do)

If you make 70 keys for Mercedes with free tokens Dolphin comes free

ok now here is where they get you tho the clamps and extras

High Security Automotive Clamp and BONUS: HU66 Clamp for VW, Audi and Porsche

so you get two clamps

and there are a few more

engraving clamp 300

single sided clamp 200

home dimple clamp 300

tubular key clamp 195

tibbe key clamp 150

mercedes h64 clamp 99

hu162t vw clamp 99

one side toy2 adapter 99

sip22 fca adapter 99

and another 100 in cutters for those

that’s almost another 1700 dollars in extra clamps you would need to get to kit this out

xhorse has the m3 jaw and the m4 jaw.

And more…

xhorse Dolphin test reports:

I have it. Till now cut hu64 keys and a couple of sip22 from fiat, 1 hu66 and work ok

It doesn’t need constant internet connection.

internet is need only to register app and login APp , and download database
then you can be offline
also if you cut one side key , after Dolphin start cutting , you can disconnect tablet / phone and it will finish cut
if you have 2 side key , and you disconnect tablet / phone during key cutting , Dolphin will cut one side , and to start cut another side you need reconnect.

Xhorse Dolphin in stock here:

http://www.vvdishop.com/wholesale/xhorse-condor-xc-dolphin-key-cutting-machine.html