Xhorse Condor Mini Plus II Error Code 56 Solution

If had an error code 56 problem with your Xhorse Condor xc-mini plus ii key cutting machine, here is a working solution.

Error code 56

The cutter is short circuited, check the cutter conductivity.

Solution:

First of all, as the error code indicated check the condor ii conductivity as follows:

How to Check Xhorse Condor XC-Mini Plus II Conductivity?

If none of the cables are broken, you can ignore the conductivity problem.
If the machine shuts off as it’s starting to cut, do the following:

Remove those screws to take off the machine screen

Find out the main board of xhorse condor ii, then remove the resister (marked red in the last image) and short it up.

Xhorse Condor II Breaks Cutter 1.5mm when Calibration?

Problem:

I have a problem with my xhorse condor mini plus 2! I am new at this work. I have broken 4 milling cutter (1.5mm) the latest I broke is yesterday when i make a update and I want to recalibrate  I use 1.5 mm cutter for calibration. when I start the machine I put hon66 calibration key but not a blank key I have used this key before for calibration and It broke 1.5 milling cutter.

Solution:

You set the blade speed to the highest speed. Don’t put max speed. The rule is to slow down.

Use cutter 2.5mm to cut any type of key without changing. You will not find any problems at work.

If not working, put di-electric compound on the tip of your probe and cutter. After that do an electric conductivity test before calibrating under the device information tab at the bottom of your Keytool Max or Xhorse App. It sounds like you’re probe and/or cutter is not getting proper electrical conductance.

Xhorse Condor II Failed to Decode Renault Clio VA2EH2?

Problem:

I had some issues last days with my Xhorse Condor Mini plus 2 key cutting machine.

I wanna cut emergency key blade for a Renault Clio from 2017. The key blade was not on the list.

Strange because there is a lot of new Renault’s with keycard. Ex. Clio 4, Captur, etc.

Machine showed and cut a little different key. So it’s not opening the car.

Solution:

Option 1:

Just use universal duplication.  Clean original key and use universal duplicate

Option 2:

look under VA2EH second one down. You’ll see it has a different series. Decode under that and cut.

Number 2

Feedback:

universal solution works. I can confirm that.

Xhorse Condor XC-Mini Plus Cut Ford Transit FO21 Tibbe Key

 Xhorse Condor XC-Mini Plus Key Cutting Machine supports to cut FO21 tibbe keys for Ford Transit and few Jaguar cars. It needs to install M3 Clamp Fixture. Following I’m gonna show how to cut a 2012 Ford Transit Connect tibbe key.

Step 1. Put the key flat on M3 clamp, and install to Condor Mini Plus.

Step 2. Get its key code: 424312.

Step 3. Select car model, follow the prompts to start cutting:

Put it flat on 0 position.

Move it to the 2 position. Press “Cut”…

Move to 3 position. Press “Cut”…

Move to 4 position. Press “Cut” …

Moveto2 position…

Move to 3 position…

Move to 4 position…

Flip the key completely 180 degrees.

Just repeat the above process on the other side of the key.

Once it’s done, it should look like this, cut from both sides.

That’s pretty much it.

It’s really easy. The new key can open all doors!

This is how to cut a FO21 tibbe key with Xhorse Condor Mini Plus.

www.vvdishop.com

How to Avoid Xhorse Dolphin Condor Probes Breaking?

Sometimes your Xhorse Dolphin or Condor key cutting machine will break probes when it tries to decode key blades.  Here’s the useful tips to solve or avoid probe breaking problem.

1). Update the app and software. Keep app and software up-to-date.

2).

Check if battery is good. Make sure the charger it’s not connected and keep a good backup amount just in case.

3).

 Always clean blade well before decoding. Probe knows it is touching the key by an electrical circuit being completed, if you break a tip itsa because the circuit didn’t complete, dirt is the reason.

And always have 5 or 10 probes in stock. The xhorse key cutting machine uses electric current to detect the blade, if it has dirt or grease on the blade, it will break.

The blade is too dirty and has no electrical conductivity.Or the key blank isn’t clear enough. Clean it with alcohol first.

4). Recalibrate the machine.  Calibrate it again when you get the new one and will make sure about the blade.

5).  Do a conductivity test/ electrical conductivity measurement to roughly test which is abnormal, probe or cuter. The probe decodes keys using electrical conduction and sometimes the probe gets light surface rust preventing it from reading your key properly. There is also a conductivity test under the Device Information tab on the app.

Xhorse Dolphin XP005 Electrical Conductivity Measurement?

6). It may be that the ground wire inside the machine is broken.

Sometimes, there’s a ground cable that needs to be replaced. That’s the one that detects, but this need replace only when prob breaks all the time. You need to open the machine and change it.

Check instruction here

Other option:

Take the optical reader (xhorse key reader decoder) it prevents breaking guides.