Renault Megane 3 Pinout to Xhorse VVDI Prog

 Can you read eeprom/flash for Renault Megane 3 UCH (v850 processor) with xhorse vvdi prog?

vvdi prog read it with no problem.

check pinout to vvdiprog

For vvdi program, don’t select 4-Immobilizer->Renault->Megane UCH
But go direct to the mcu and select the right type and read.

Select 2-MCU->Renesas V850-> D70F3384 for example.

VVDI Key Tool Plus Read MQB D70F3537 with Xhorse MQB Adapter

 Xhorse MQB48 Solder Free Adapters are specially designed to provide an easier and safer solution to save automotive locksmiths from the intricate and annoying soldering, pin lifting and wire cutting work. Here we’ll walk you through how to read MQB D70F3537 data with the new adapter and Xhorse VVDI Key Tool Plus.

If the MQB48 solder-free adapter is not used, locksmiths may suffer from the complex operation and high risk of damage when reading VW MQB instrument immo data particularly BGA D70F3532/35/36/37. Possible problems are:

• Crystal oscillator frequency configuration failed.
• Difficult operations requiring experience and skills.
• Easy to cause damage and high risk of loss.
• May require the use of professional tool.

Procedure

Immo programming >> VW >> Select by type >> MQB instrument immo system >> Instrument-MQB48(VDO/JCI-NEC35xx lock) >> Start programming

Please read the disclaimer carefully, tap “OK”.

Please make sure Network connection is normal, click “OK”.

Programmer reads files >> Read NEC35xx chip >> Adapter method >> D70F3537

Here we can check the connection diagram.

Connection

Step1. Located the positioning points and connect the adapter to the board with reference to the points, connect and apply the clips.

Note: make sure the pins aim right at and keep good contact with the points. Otherwise, the following errors may occur:

• Crystal oscillator frequency configuration failed. There’s a problem with the contacts, please reinstall the adapter.
• Chip cracking failed.
• The contacts are loose.
• Continue reading repeatedly.

Step2. Connect XDNPM1GL MQB48-BGA Adapter to Key Tool Plus with DB15 cable.

Step3. Power it up using a power supply.

Read MQB48 IMMO

Read >> Continue

Reading success.

Save data file.

The immo data can be used to generate dealer key and for key learning.

Obtaining immo data >> Load and upload NEX35xx chip file read by Key Tool Plus>> Select the saved data

Is this instrument type is requires external EEPROM 95320 to be loaded: after 17 years of PASSAT(56D902861A/ 56D920871A/ 56D920871/ 56D920861), after 17 years of Beetle

Click “Yes” to start loading external EEPROM data files.

Click “No” to start uploading data to the server.

This instrument requires no reading and loading EEPROM 95320, so here we tap “No” to start the calculation.

This will take about 5-10 minutes to complete the calculation.

www.vvdishop.com

Ford Airbag FL3T-14B321-BD Pinout to Xhorse VVDI Prog

Where to find the xhorse vvdi prog connection diagram for Ford airbag module to clear SRS crash?

Infineon xc2336a
FL3T-14B321-BD

Solution:

You are able to read it with vvdi prog by using the diagram below and disconnecting VCC from programming pads and connecting the external 12v to the pin on the top left corner. Flash3 contains crash data.

www.vvdishop.com

Xhorse VVDI Prog Read BMW 2005-up Facelift CAS

 Question:

Where to find the wiring diagram for connecting xhorse vvdi prog to BMW E65 Facelift CAS？

I am replacing a dead module that will not accept keys with a used one and need to read ISN from old so I can transfer to new one and sync Dme and cas. This is my cas module type:

Solution:

Here is the procedure.

CAS reads as MC9S12DG256. Only eeprom is needed. Read eeprom, change isn and vin of new CAS to car original isn and vin.

Write eeprom back to CAS, do DME-CAS alignment and you are done.

BMW E65 Facelift CAS connection diagrams to vvdi prog

BMW 7 series CAS 2005-up facelift

www.vvdishop.com