Program Fiat Stilo 2004 AKL with Xhorse Key Tool Plus

Fiat stilo 2004 all keys lost is done by xhorse vvdi key tool plus via dump.

Chip in the car started at the quarter.

Device required:

VVDI Key Tool Plus Pad

Xhorse VVDI Prog

Xhorse VVDI Super Chip XT27

Magneti Marelli HC912 ECU

Procedure:

1. Read EEPROM with VVDI Prog

BCM Mask MC912DG128ACPV 3K91D

Follow wiring diagrams below to connect mcu with vvdi-prog

Read and backup MC68HC(9)12 MC912DG128 unsecured EEPROM and Flash data

2. Write Key with Xhorse Key Tool Plus 

Transfer data to key tool plus

Check: How to Transfer Data from Xhorse VVDI Key Tool Plus to PC?

Read 5-digit PIN code and program super chip transponder keys successfully.

Under menu: Immo Data Tool-Fiat-Stilo- 2000 onwards- Magneti Marelli HC912

Xhorse Audi BCM2 Solder Free Adapter, Worth Buying?

 To program VW Audi 5^th IMMO keys like A4, A5, Q5, A6L, A8L, Touareg, Xhorse BCM2 Solder Free Adapter would help a lot. Users can easily select the corresponding method on VVDI Key Tool Plus to work with it.

There are mainly 2 types of car models in programming Audi 5^th keys:

• Models that no need sync data.

This type of models only need to get immo data for key adding & all keys lost. The representative models are A4, A5, Q5.

Ways to get immo data:

1. For vehicles before 2012, can use VVDI to read by OBD directly; Or use VVDI PROG + VVDI2 to read & decode D-FLASH, P-FLASH from BCM. This type of non-encrypted BCM can be used for BCM clone & maintenance with VVDI PROG.
2. For vehicles after 2012, Audi BCM2 Solder-Free Adapter is necessary to read immo data. After that, users will be able to convert data via VVDI2 or VVDI Key Tool Plus for key match.

Note: Data read by Xhorse BCM2 Adapter is only used for key programming, no support BCM clone maintenance.

Suppose that you don’t have the Audi BCM2 Adapter when all keys lost, you may have to pay an additional cost $170-$500 for data calculation via OBD. With the adapter, all these are free.

• Models that need sync data.

This type of models need to get immo data & synchronous data simultaneously. The representative models are A6, A8, Touareg.

For key adding situation, either VVDI2 or VVDI Key Tool Plus can get immo data by OBD regardless of years. Users can get synchronous data from a working key without having to read BCM. It’s very relatively simple.

For all keys lost situation, certain CVT gearbox of vehicles before 2012 support to read BCM data via VVDI PROG. Then users can follow steps on VVDI2 or Key Tool Plus Pad to online calculate synchronous data.

(*Few cars are workable in this way, it requires experienced locksmith to read directional lock and engine data, short circuit communication line. It’s not recommended to do without experience.)

As for vehicles after 2012, those BCM are generally locked. At this time, the Audi BCM2 Solder-Free Adapter can help to read out data. After that, users should convert immo data via VVDI2 or VVDI Key Tool Plus. If it allows to read directional lock and engine data again, which means it supports to get synchronous data for all key lost programming. If not, users should find third-party calculation.

Price Difference

1. Xhorse Solder Free Adapter is a one-time deal, only cost $121 to support many Audi models.
2. Without adapters, users may have to pay $500 and more for data calculation.
3. Calculation cost with data read by Xhorse adapter will be much lower than simply read by OBD.

Conclusion

It’s recommended to have Xhorse BCM2 Solder Free Adapter for locksmiths who usually program VW/Audi 5^th immobilizer system keys. The adapter not only greatly save cost, but also earn more for next time job. It will pay for itself once using it.

www.vvdishop.com

Convert Ford/Mazda ID83 4D-DST80 to ID63 4D-DST40

 How-to: Convert Ford/Mazda ID83 4D-DST80 to ID63 4D-DST40 with xhorse vvdi key tool max by manually input parameters.

Here is only converting id83-id63 only. I’m pretty sure it can be done vise versa.

You can’t clone most ID83 80bit keys. True 80 bit ford keys can’t be cloned.  You can clone 4D83 bit for Focus and Kuga models ONLY via xhorse super chip xt27.
Clone 4d63 80 bit is not problem.

You can generate one and program it via obd easily.

Read this chip right here, it is 4D83 DST80

Convert to this one which is 4D63 DST40

Here we show you how to change it manually.

this is actually working on a Ford F150.

I have dst 40 but i need dst 80 at this time.

Let me show you how to switch it back.

I think you can go back and forth.

Read this one you got a chip on that

so right now it’s a 40 83 cloneable dst80

so what you do is click Edit and click that DST+

then when you see it’s a 4083

right click that P30

Change to 0046, press OK

once you press ok

you need to press this ‘write’ icon but not convert button

press this icon

xhorse key tool max says p30 write data as 0046

You’re gonna read it again go back now

Still have the same chip on top and read it

There you go, it is 4063 dsd40

i’m pretty sure you can go back and forth

or you can actually just generate it because you have it here

www.vvdishop.com

How to Solve Xhorse Dolphin XP005L “Error Code:33” When Cut TOY40?

 The TOY40 emergency key is very thin, only 1.5mm with one side. So if using 2.5mm cutter, Xhorse Dolphin XP005L will give a 33 error code. Following I’m gonna show how to decode & cut it.

For Dolphin XP005 or Condor XC-Mini Plus key cutting machine, you’ll need to use M2 clamp & bar adapter. New Dolphin II M5 clamp can cut without bar adapter.

Decode Key

Vehicle database >> Asia >> Toyota >> TOY40 emergency key(one side key)

Install the original key on M5 clamp side B, tip align 2^nd position.

Press “Decode key”.

The Dolphin II will start decoding, just wait until completed.

Its bitting codes have been read out.

Cut Key with 1.5mm Cutter

Install new key blank on M5 clamp, press “Cut key”.

It mentions “Error code:33, cutter diameter tool large.” while the warning red light is flashing. That means the TOY40 one side key cannot use with 2.5mm cutter.

So let’s change the cutter to 1.5mm.

And remember to save new cutter diameter on machine:

System >> Machine parameter >> Cutting setting >> Cutter diameter: 1.5mm

Go back to re-cut again.

Xhorse Dolphin II can normally cut key now…

Cut key success.

Done.

https://www.vvdishop.com/service/xhorse-dolphin-xp005l-toy40-error-code-33-solution.html

Benz w203 mask 1j35d change KM wiring diagram to VVDI Prog

 Here goes the scheme of Mercedes Benz w203 mask 1j35d to do full back-up on both processors.

Xhorse vvdi prog will put in the next update the scheme because they only have for EEPROM with immo and not the one with coding and km.
Have a beautiful day everyone.