Renew Chrysler Smart Key with Xhorse VVDI Key Tool Plus

 Today we are going to unlock another smart remote key for Chrysler/Jeep/Dodge with xhorse vvdi key tool plus.

FCC ID M3N-40821302

PCF7953

In key tool plus, we will read transponder and show you that this is a used key.

Select Special function- Remote Renew – Chrysler – M3M Hitag2

It shows you if there is an available xhorse renew adapter for it

We have two options to renew this key, we choose the adapter because we have the renew adapter. Don’t need to use the wire.

Place the Chrysler key circuit board on the adapter, Secure it

Press Unlock

We successfully unlocked the chip the remote has been renewed.

It said unlocked.

www.vvdishop.com has the wiring diagram of remotes, check remote unlock wiring diagram.

How to Add KeylessGo to Mazda3 with Xhorse Smart Key Box?

 Xhorse Smart Key Box can be used to add keyless entry/ keyless go functions on 2018 Mazda 3 successfully. Before that, I’ll use Xhorse VVDI Key Tool Max + MINI OBD Tool to add a remote and demonstrate how it works.

• Generate Smart Remote

Remove PCB board from key shell to be programmed, place it on the VVDI Key Tool Max coil.

Vehicle remote >> Mazda >> 3 hatchback(2014-208) KeylessGo ID49 315M >> Generate

Burn success.

• Program Smart Remote

Insert MINI OBD Tool into the vehicle OBD port,

Immo programming >> Mazda >> Select by regional car model >> USA >> Mazda3 >> Smart key system >> 2017- >> Start execution

Follow the prompts to operate:

Take all smart keys out of car.

Press start button of vehicle for 10s, then press start button again when the indicator light of start button changes to yellow.

Operation completed!

Add a key >> OK >> Yes

Please switch ignition on.

Current number of smart key: 3

Read the password…

Completed to read password, press “OK” to match.

It’ll take about 7 minutes to configuring the system, please wait…

Step on brakes when automatic-shift, step on the clutch when manual-shift and keep the mark end of the smart key to be programmed close to the start button, take other keys out of the car.

Key matched successfully!

Current number of smart keys: 4

After testing the remote successfully, move to next step.

• Install Smart Key Box

1. Solder the connections.

Find the included 10-wire rainbow connector and take note of which wires relate to which buttons on the board to make sure the wires are soldered to the correct points.

2. Insert to Smart Key Box, turn on Dipswitch position #2(for Prox vehicles).
3. Connect Smart Key Box with vehicle properly. (power line, HF/LF antenna, OBD cable)

Sync Remote & Smart Key Box

1. Holding the learning button until hearing a beep and LED is ignited.
2. Open Smart Key Box app, press “connect the car”.
3. Press any Onscreen button to bind phone to the app.

(The Smart Key Box can save and connect 6 remotes or phones at a time in addition to car remote count)

4. Once all were done, holding the learning button again to exit learning mode.

• Test The Remote

Place the Smart Key Box safely under seat/dash cavity. Let’s go out to have a test.

Keep the phone screen to test by leaving vehicle and approaching to check all settings are working.

– Go away, it locks.

– As soon as I get to the car, it unlocks.

Perfect done!

This is how to use Xhorse Smart Key Box to work on a 2018 Mazda 3 successfully.

https://www.vvdishop.com/

VVDI Mini Key Tool Renew Nissan Smart Key via Renew Adapter

 This is a Nisan smart key FCC ID

PCB A2C32801600
FCC ID KR5S180144014

Is it already locked once you program it to a vehicle the chip locks it into that vehicle
In xhorse vvdi mini key tool app, go to Special function- Remote Renew – Nissan – 315mhz hitag2 smart key A2C53297341

FCC is the same, 4 buttons

It shows you if there is an available xhorse renew adapter for it

We have two options to renew this key, we choose the adapter because we have the renew adapter. Don’t need to use the wire.

Place the Nissan key circuit board on the adapter, Secure it

Go ahead and press Unlock

We successfully unlocked the chip the remote has been renewed
We read Nissan smart key to make sure we successfully unlocked it.
It said unlocked.
For those who don’t have the renew adapter, you can renew key by soldering there is a connection diagram.

www.vvdishop.com has the wiring diagram of remotes, check remote unlock wiring diagram.

How to Renew Benz ECU ME9.7 with Xhorse VVDI MB?

 Here’s a quick easy guide on renewing Mercedes Benz ECU ME9.7 with xhorse vvdi mb tool through OBD

For connection, check the previous post: connect VVDI MB Tool to ME 9.7 ECU

Select Renew ECU/Gearbox Function
Select ECU

Read ECU information
Get Erase password

Press Renew
If failed to erase target unit, renew again

Renew ECU success

Save data

 www.vvdishop.com

How to Clone 2014 Fiat Doblo key with Xhorse Key Tool Max

 How to use Xhorse VVDI Key Tool Max to clone a spare key for 2014 Fiat Doblo? It’s very fast and easy, following I’ll show the procedure.

An original working key, a blank new key and a VVDI Super Chip are required.

Put the original key into Key Tool Max coil, press

Transponder clone >> Read transponder

Information has read out, it’s cloneable.

Just follow the instructions to clone, continue to press

Clone >> Start clone >> 46 transponder clone >> Original key clone(recommended)

Note: don’t remove the original key

It’s asking to sniff at the data, so what I have to do is to put the antenna near the ignition and turn it on.

Put the original key into Key Tool Max coil again as required.

Wait collecting data…

Calculate success.

Take out the original key, then put a Super Chip into coil.

Write data success.

Let’s put the Super Chip inside a new key shell to have a test.

As you can see, it starts the vehicle.

Let me try the original one, both can start the car.

It is a very simple process with VVDI Key Tool Max to clone a key for 2014 Fiat Doblo. It only takes me 4 minutes to finish.

https://www.vvdishop.com/