Xhorse Dolphin XP005 M5 Clamp Cut Toyota Prius TOY48 All Keys Lost

Xhorse released an update on the app that users can now use the M5 Clamp, which is a combination of M1 and M2 clamp on the Dolphin XP005. So I went on www.vvdishop.com and for about $249 dollars. I got a clamp. I’m gonna unbox it here.

I’ll put the M5 clamp on the machine to try it out. I do have to update my firmware and Xhorse app for this function. In terms of M5 clamp type, vacuum seal it is to keep it fresh, I guess.

The cool thing about M5 clamp is that I don’t have to keep swapping them. Just open it all the way up and rotate it over to the B side, which is like the M2 clamp. You don’t need to swap the clamp back, which is really nice if you ever doing a lot of keys in one place.

So I’m going to go ahead and loosen out slide off the M1 clamp. Do a little house cleaning , then install the M5 clamp. Crank it down, power on the machine. To be sure, M5 clamp doesn’t need a calibration, but it needs to be set up.

Open app, connect to Xhorse Dolphin:

Device information >> Cutting setting >> Clamp >> M5 >> Set parameters

Setting parameter success.

Following I’m going to cut a Toyota Prius TOY48 key for a test.

All keys lost >> Toyota >> Inter key code: 46081 >> TOY48

It says to use M5 clamp B side, tip align line 2.

I have a Dolphin 2 as well. The knob is actually different. But as long as it works, it doesn’t really matter. After tightening the key blank, here we go.

OK >> Cut key >> Cut

The Dolphin starts cutting…

After finishing, flop it around to cut the second side.

Key cutting is now completed.

Take out the key to test if it works.

Alright, key goes in, and it turns perfectly. There’s no calibration here but M5 clamp can actually index the key and cut by code well.

This is the M5 clamp on Xhorse Dolphin XP005 key cutting test review.

www.vvdishop.com

Tips to Cut Shoulder Stop Keys with Xhorse Condor Dolphin?

 Here are the tips to cut shoulder stop keys on the Xhorse Condor or Dolphin key cutting machines.

Definitely easier to use it than to eyeball it. We are going to show you how to use the shoulder stop with it.

This is our M1 jaw and we see on the jaw there is actually a groove right here milled into it.

The shoulder stop has a little lip on it and that little lip actually fits into that groove and that actually acts as your shoulder stop.

We are going to cut a Suziki motorcycle key.
Suz18 isn’t in the Dolphin xp005 software. You can cut Suz18 under YM63 and we got the key code by Lishi.

We are doing a duplication for the bike.
Let’s grab the vvdi key tool max. We are already connected.
Go to All Keys Lost->Yamaha, put code A7354 and you need the internet to actually use the code search on it.

Pulls it up tells us M1 clamp shoulder align and 2 4 3 1 3 1 4 so let’s the correct bitting on there.

Our jaw clamped in there, grab the shoulder stop here.
Fit it into a little groove here, you just simply slide the key and push the shoulder stop up.

You just push the key until you know hit the shoulder stop.
Clamp it in it just takes the guesswork out of it here you don’t have to eyeball it.

basically, you’re going to do it again as you can see so you got your shoulder stop in the groove here and you just slide the key until it until it hits the shoulder stop and then just clamp it
in and then i’m going to put this back on my little magnet up here tightens my grub screw and these magnets on top of the machine work really really well.

Then now we’re all ready to cut the key here. Just go ahead and uh hit cutting key. The machine will do its thing here.

We got the key, we’ll just loosen the grub screw here pull the key out and turn on the bike.

The key works perfectly.

www.vvdishop.com

How to Cut Lexus TOY48 with Xhorse Dolphin XP005 and M5 Clamp

 Since Xhorse announced the M5 Clamp has already been compatible with old Dolphin XP005 & Condor XC-Mini Plus key cutting machine, I’m gonna have a try today. Before that, please make sure your software and firmware were upgraded to the latest version.

The M5 clamp allows users to cut high security and edge cut using the same clamp by rotating from A to B side. No more to disassemble M1 or M2 clamp again and again.

Procedure

1. Installation

The first thing we need to do is to install the M5 clamp on Dolphin XP005.

2. Set Cutting Parameters

Device information >> Cutting setting >> Selected M5 clamp

3. Cut Key

All key lost >> Lexus >> Enter lock code: 44137

As we can see, it’s telling to use the M5 clamp B side, tip align Align line 2.

Rotate M5 clamp to B side, then install a key blank firmly.

Start cutting key…

The Xhorse Dolphin can work as usual.

After successfully cutting 2-sides, take out the Lexus key for a test.

It can actually open the lock.

As expected, the Dolphin 1 can work with M5 clamp without problems! It should also perfectly do with other Xhorse Key Cutting Machines as it claimed.

www.vvdishop.com

Which Xhorse Key Cutting Machine is Better for Motorcycle Key

 It really doesn’t have any for motorcycle keys. What is a good key cutter for motorcycles?

Here’s the clue.

Xhorse Condor and Dolphin key cutting machines are mainly fro car keys, but also have a few motorcycle and household keys are on database.

The Xhorse key cutter are the cheapest it been the most reliable and most accurate key cutting machine, it also boots the quickest and has done 99% of the keys people need.

In Condor mini plus has some Motorcycle data included. So does Dolphin XP005, XP005L and Condor II.

You can use universal duplicate to duplicate a motorcycle key. You can also create custom key data.

You can create custom bitting with the app, We’ve been doing Honda and Suzuki motorcycle keys with the Condor.

You can search and download my Suzuki bitting in the app, it’s under “Hayabusa”.

Custom Key Tool for Condor XC-Mini is perfect for double sided keys or high security. You can find all the measurements of your key blank on InstaCode.

It does not have many kawasaki keys database, you need Instacode as reference to get a key blank code and then on the Cut by Bitting menu search for that key blank HON77 for example.
KW14
KW15

Condor XC009 also makes all vertical motorcycle keys.
As for key programming,  Tango and tmpro have pretty good coverage on bikes.

OBDSTAR also releases motorcycle special key programming devices.

How to Fix Xhorse Dolphin XP005 Shows M5 Clamp

 Problem:

Why my xhorse app shows my xhorse dolphin xp005 (DOLPHIN 1) to use the dolphin 2 clamp? There was a new app update. It’s happening on my phone. Everything says m5 clamp but I have dolphin 1.

Solution:

Currently, M5 clamp is not yet compatible with the dolphin xp005 key cutting machine (wait for feature firmware update). It is for Condor II and Dolphin II.

If xhorse app asks to use M5 fixture after upgrade, go to Device information at bottom right-then Cutting setting then change clamp to M1/M2.