Clone 2010 Fiat Ducato Remote by VVDI Mini Key Tool

 Had to share some very surprising news from one of our customers!!

I was working on a flip key for a 2010 Fiat Ducato, and wasn’t able to connect through to the vehicle to program diagnostically.
About to give up, so I attempted a Remote Clone with the Xhorse VVDI mini key tool and lo and behold.. it works perfectly!!
2010 FIAT DUCATO ON A B SERIES FLIP!

Some people says usually it will work perfectly for a few minutes, when you press the original remote the one you made would stop working until you start the vehicle with it.

But i tested it over and over with both keys, everything is perfect, disconnected the body power cable and reset the lot and still works 100%.

Can VVDI Mini Key Tool Generate Cloud Remote?

 Question: 

Can i use xhorse vvdi mini key tool to generate Cloud remote (remotes that are marked Cloud in the list)?

Answer:

No, mini key tool cannot generate Cloud remote.

Cloud remote has larger database, it can be generated by key tool max, key tool max pro, vvdi2 and key tool plus.

Which type of remote is to be used to generate Cloud remote?

You will need wire remotes (except B5 style) to generate Cloud remote.

Generate Ford Edge 4D 63 80 Bit Key with VVDI Mini Key Tool

 Question: I wanted to program a key for a 2011 Ford Edge the original key has a 4D 63 80bit. What is the correct chip to generate with xhorse vvdi mini key tool and program this vehicle? cloning is not possible and is not server supported.

I also used this one (83 Ford 80bits) but had no success. I have previously cloned original virgin chip and successfully programmed with vvdi super Chip. But it hadn’t generated before.

Solution:

Generate the 4D 63 not 83. Even the 40 bit should work. The 4D 83 is a completely different chip.

It is 4d 63, so use 4d 63 40bit, the so called 4d 63 80 bit is not saying it requires 80 bit chip, it means the current 63 has 80 bit capacity. If you want it to work, don’t use 4d 83.

Use this option (63- Ford/Mazda)

Pretty much all the 4d 63 chip, if you buy one on the market, it can change to 83.
Check 4d63 and add by obd.

Xhorse Not Prepare Audi XSADJ1GL VVDI 754J 868MHZ Solution

 Q: I bought a Xhorse XSADJ1GL VVDI 754J universal Smart Remote Key for Audi ( Immo 5 , BCM 2 system).  I can’t prepare 868 MHz . 315 and 433 MHz prepared ok. But when I try to create 868Mhz with vvdi mini key tool I get key with 433 MHz. It seems that is 434 but works good after programming. Any have idea?

The board key has marked AD006 Ver 1.1.

After generate 868mhz remote, both mini key tool and keydiy kd-x2 detect the frequency as 434mhz.

Solution:

Kd and mini key tool xhorse cannot read 868mhz that’s why. 868MHz signal is weak. Sometimes cannot be detected by major key tools on the aftermarket.

VVDI 754J AD006 is new one, old one was just 315, if he generates 433mhz and 315mhz, = is new pcb. (The Key produced before 20.04.22 can’t be prepared with other Mhz)

It works just try it. It keeps showing 434Mhz but it works.

IT shows 434 But IT will work as 868mhz. Just generate IT and code to car. It works fine after programming.

Can I Renew BMW PCF7944 Key with VVDI Mini Key Tool

 Need renew bmw keys, chip different, PCF7944, will xhorse vvdi mini key tool do it?

Solution:

This PCF7944 is the 1st generation of this type keys.
7944 can’t renew but can program to car by back door. Pcf7944 keys are cheap also.
This cheap can be fully read out, then its data can be successfully written to cas 2 or cas3
Use proper programmer to adapt to CAS.
But you need to remove CAS.