Xhorse VVDI2 Small Screen Show Updating in Chinese?

 Problem:

Pulled Xhorse VVDI2 out of box this morning plugged it in and the small screen shows updating icon in Chinese. Any idea?

Possible reason:

You unplugged the USB cable before the upgrade was fully completed last time. So it shows in upgrade status.

Solution:

1.Update VVDI2 firmware via Xhorse Upgrade kit on laptop.

2. Change USB port or another laptop, try again. If all fails, the device may need a factory repair.

www.vvdishop.com

How to Add Audi A8 2018 BCM2 Key by Xhorse VVDI2

 It is an Audi A8 2018, and it’s a keyless one with a push-to-start key. We will walk you through the entire process using the Xhorse VVDI2 key programmer. From setup to completion, you’ll see all the steps needed to successfully create a copy of an advanced keyless system.

Tool used:

Xhorse VVDI2

Xhorse vvdi key tool max

Xhorse XM38 754J remote

Original Audi key

Step:

Generate remote

Read Immo data

Make dealer key

Learn key

Procedure:

1. Generate remote

Generate remote under 754D Prox 868 option using XM38 754J remote

Step 2: Read Immo data

Run VVDI2 software.

Select Key Learning-> 5th Immobilizer system
Then hit Read BCM2 Data (OBDII)

Save immo data

Step 3: Make dealer key

Press Make dealer key

Prepare normal dealer key

Select A6L, A7, A8, Touareg add key

Put original key into vvdi2 programmer.

Load BCM2 data read in step 2.

Make dealer key successfully.

Step 4: Learn key

Select Key Learning.

Follow VVDI2 prompts to learn both keys.

All keys have been learned.

www.vvdishop.com

Xhorse Multi Prog Peugeot PSA Valeo V56.12 Pinout

 Question:

I have to read a Citroen C3 1.2 Petrol ECU V56.12 but the wiring connection in Xhorse Multi Prog Boot Mode is missing.

Solution:

Multi Prog does PSA Valeo V56.x in boot mode only.

Here is the boot mode pinout.

Read 2008 VW Toureg Kessy IMMO Data with VVDI Key Tool Plus

Problem:

It is a 2008 VW Toureg with Kessy module. Weld up and read back-up data with xhorse vvdi key tool plus successfully. But it fails to read immo data. Tried several times. Welding is good.
What could be the problem?

Solution:

Don’t have to read immo data from the Programmer menu.

Go through the IMMO menu and loaded the “backup data” you read with the programmer, and it will give the the pin and 7 byte cs code.

Go to this screen and load the data you’ve read.

Same system as 2008 Porsche Cayenne.

Will VVDI Key Tool Max Pro Add Peugeot Marelli ID48 Key

 Question:

Will Xhorse VVDI Key Tool Max Pro Add a Key to my Peugeot Boxer 2.2 2009 with magneti marelli immo?

Yes, key tool max pro will add a spare key to Peugeot Citroen ID48 with Marelli IMMO system.

Go to IMMO system (Marelli 70F3238 + 95320 ID48) function.

Supports read eeprom, write eeprom, make dealer key, key programming, adapt remote key and renew remote.

If need to add a new key, follow steps below to finish key programming.

FYI:

If your car has id46 transponder then no problem for you, can use precoded transponder and program in car via diagnostic device but if is immo3 with id48 than you need special precoded id48 chip from vin from dealer or need make transponder with key maker from dump and need rewrite new dump which will be produce during transponder programing. in this mean the transponder is ready to start car.

www.vvdishop.com