ابزار Xhorse VVDI

Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزار

ابزار Xhorse VVDI

Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزار

عناوین یادداشت‌ها

  • VVDI Key Tool Plus BMW CAS4+ No Smart Function Solution پنج‌شنبه 30 مهر 1405 12:06
    The car is a 2012 BMW 535i, F10 chassis, N55 engine, with a CAS4+ system. It arrives with a deceptively simple complaint: the key’s proximity function doesn’t work. Pressing the brake and the start button does nothing. To switch on the ignition, the key must be held against the induction coil. The customer bought the...
  • VAG MQB49 5C Xhorse XSMQB Key Weak Signal Solution سه‌شنبه 28 مهر 1405 11:59
    Share the solution regarding the customer’s XHORSE XSMQB smart key weak signal issue. “Read original MQB49 5C key data ok, but sometimes it doesn’t learn Xhorse XSMQB smart key. Xhorse has a wea signal and since it is keyless you need to disassemble the steering column and pop the Start/Stop button out. Then hold it...
  • Read Skoda Scala 2023 MQB49 5C key with Xhorse دوشنبه 27 مهر 1405 11:56
    Problem: Tried to read 5C key on a Skoda Scala from 2023. But in Xhorse VVDI Key Tool Plus and Multiprog not the right PCB schematic. Does anyone know the right connection diagramm ? Here is the clue. Pinout is attached. Or use 5C solder free adapter without soldering. XSMQB1EN works make sure you generate the right...
  • Xhorse Key Tool MIDI Program 2020 Ford Fiesta Smart Key جمعه 24 مهر 1405 11:30
    Adding a spare smart key to a 2020 Ford Fiesta is a straightforward process when using Xhorse VVDI Key Tool MIDI / Key Tool Plus . In this guide, we walk through the steps to add a new key to a Ford Fiesta after confirming that the original key was no longer working. Step-by-Step Procedure 1. Select the Correct...
  • Xhorse Multi Prog Clone Audi A6 C5 Cluster via BDM پنج‌شنبه 23 مهر 1405 11:56
    Xhorse Multi Prog programmer new user review: Audi A6 C5 cluster swap: cloned via BDM On this cluster the immobilizer is built in, so the original EEPROM has to move with the car. Motorola MC68HC912DG128A, read and written over BDM through 4 test points on the board: VCC, GND, BKGD, RESET. There are already new...
  • Program 2024 Opel Corsa F Flip Key with VVDI Key Tool MIDI چهارشنبه 22 مهر 1405 12:28
    Successfully programmed a 2024 Opel Corsa F flip key when all keys lost using Xhorse Key Tool MIDI programmer. Step 1: Read PIN Code Decode door lock with Lish auto pick. Go to IMMO Programming- Peugeot- Password Reading- Type 3 CAN (adding). Select Read Password. Turn off the ignition switch. Switch ignition off and...
  • Xhorse Key Tool Max Pro Add 2026 Renault Kiwi Flip Key سه‌شنبه 21 مهر 1405 11:55
    Added a spare flip blade key to a 2026 Renault Kiwi with Xhorse Key Tool Max Pro successfully. Continental version. Set up bench connection with key tool max pro. Need to find proper pinout to UCH and antenna. Read UCH module data. Extract ISK and PIN Code. Then program flip keys. Images attached:
  • Xhorse Multi Prog Clone Chevrolet Delphi MT80 ECU دوشنبه 20 مهر 1405 11:21
    Xhorse Mult Prog cloned a GM Delphi MT80 engine ECU successfully. It’s a Chevrolet Cruze 1.6 MY2010 with a Delphi MT80 ECU. Read and write in boot mode. Read ok. Write ok. Multi Prog supports checksum correction for this ecu.
  • Read Kia Soul 4A Smart Key Pin Code with Xhorse Key Tool Plus شنبه 18 مهر 1405 11:44
    The Xhorse VVDI Key Tool Plus Pad will pull the PIN code for 2019-2022 Kia Soul, which has the newer style key with a 4A chip. Autel IM508 has consistently failed on the newer Kias, so the key tool plus is the go-to for this step. Read the PIN code with the Xhorse Key Tool Plus: The process begins by reading the 4A...
  • How to Modify Xhorse Nissan Style Smart Key Buttons جمعه 17 مهر 1405 11:23
    Problem: After generating an Xhorse XSNIS2EN Nissan smart remote and program to a 2015 Nissan Altima (ID47 chip type), the car starts, but the Xhorse key trunk button triggers the panic function. Solution: Button functions may need to be customized afterward to match the vehicle’s layout. To fix this: Go to More →...
  • Clone Renault BCM N3 with Xhorse Multi Prog پنج‌شنبه 16 مهر 1405 11:52
    Xhorse Multi Prog new user feedback: Cloning a Renault Kangoo/Mercedes Benz Citan BCM-N3 (Renesas V850 MCU) using Multi prog programmer. Read the P-Flash (program memory) and D-Flash (EEPROM data/immobilizer) from the original Renesas D70F3376A MCU microcontroller and wrote both to the donor unit. Read Dflash &...
  • VVDI Key Tool Plus Read BMW Locked B48 DME ISN چهارشنبه 8 مهر 1405 11:22
    Xhorse VVDI Key Tool Plus released a new software update: BMW B48 LOCK (Read). Read locked BMW B48 DME ISN. Read-only. Cannot write. Example: Read 2022 BMW X1 B48 DME ISN on bench mode with Bosch ECU adapter.
  • Xhorse Multi Prog Repair Audi G85 Steering Angle Sensor سه‌شنبه 7 مهر 1405 15:06
    The Audi G85 steering angle sensor (part number 4M0907129HA, equipped with the D70F4000 chip) is a critical component in modern Audi vehicles. When it fails, drivers may experience warning lights, loss of power steering assistance, or communication errors with the vehicle’s ECU. This article provides a general...
  • Xhorse VVDI Key Tool Plus Update Multi-language Database دوشنبه 6 مهر 1405 11:49
    Xhorse VVDI Key Tool Plus updates the database to support multiple languages. Supported multi-language list: English Thai Turkish French Hindi Russian Portuguese Spanish Indonesian Polish Korean Hebrew Italian Vietnamese German Ukrainan Chinese Persian
  • Xhorse Multi Prog Read 2018 BMW MG1CS201 ECU پنج‌شنبه 2 مهر 1405 13:12
    This article provides a step-by-step overview of reading the engine control module from a 2018 BMW X1 equipped with the B38 engine (Bosch MG1CS201 TC298TP), using the Xhorse Multi Prog programmer. Before You Begin: Identification Is Everything Before starting any operation, it is critical to identify the exact ECU...
  • Xhorse Super Chip XT57 for Toyota Yaris 4D70 All Keys Lost چهارشنبه 1 مهر 1405 13:21
    Here we share one of our customers’ working experience on programming a Toyota Yaris 20019 all keys lost. It’s blade key Toy47 4D type. This one no way by obd. Read eeprom and add the key by dump mode. Eeprom only, you’ve done the hard part getting the box out, read 8 leg, write back and plug in to start. Did the...
  • VVDI Key Tool Plus Disable Ford Alarm without AKL Cable سه‌شنبه 31 شهریور 1405 11:27
    Xhorse VVDI Key Tool Plus has a new feature to back up eeprom data and generate a universal key to disable active alarm on newer Fords. It does on some Toyota, it reads eeprom to and then on an XM38 it uses it as emergency, then with another different xm38 will be your “master” key to program in. No Ford AKL adapter...
  • How to Add 2011 VW Jetta Key with Xhorse Key Tool MIDI via OBD دوشنبه 30 شهریور 1405 11:57
    VVDISHOP here will show how to add a spare ID48 remote key to a 2011 VW Jetta using Xhorse VVDI Key Tool MIDI . Procedure: Step 1: Generate Remote Generate Xhorse remote under the proper remote program. Step 2: Generate Transponder Go to Generate Transponder function Generate an ID48 (48 TP23 VW) transponder using the...
  • Xhorse Multi Prog Repair BMW G12 Tail Light Data جمعه 27 شهریور 1405 12:52
    On this BMW G12, the right tail light was completely black. The fault was in the tail light data, so instead of replacing the lamp, I opened the unit and repaired the MCU data with the Xhorse Muti-Prog Programmer. Remove the Tail Light Pry off the side trim beside the tail light. Remove the lower tailgate trim as...
  • Xhorse Key Tool Adds 2022- Hyundai Kia 4A Remote Database پنج‌شنبه 26 شهریور 1405 11:34
    Xhorse VVDI Key Tool series released new Hyundai/Kia 4A keylessGo smart key generation remote database on September 17th, 2026. This update can be applied to vvdi mini key tool , key tool max , key tool max pro , key tool midi and key tool plus . KeylessGo: +ADD Kia K8(2022) ID4A 95440-L8010 +ADD Kia K8(2022) ID4A...
  • How to Solve Xhorse Toyota Remote Red PCB Write Error? سه‌شنبه 24 شهریور 1405 11:29
    If you work with Toyota smart keys and remote generation, you may have recently noticed a significant change in the hardware being shipped by Xhorse. The new stock of XKTO series Toyota remotes ( XKTO24EN , XKTO25EN , XKTO22EN etc.) has arrived with a Red PCB, replacing the previous Green PCB versions. Because many...
  • VVDI Key Tool MIDI Program Havel H6 2020 All Keys Lost دوشنبه 23 شهریور 1405 12:46
    Xhorse VVDI Key Tool MIDI programmed Haval H6 2020 all smart keys lost successfully. Step 1: Generate remote Generate an Xhorse remote with the proper remote program. Step 2: Program key Go IMMO Programming- Havel- H6- KeylessGo- Knob type PEPS system Select All keys lost mode 1 (Not Clear K-SK). Enter restore EOL...
  • 2024 Geely Coolray Pinout to Xhorse Multi Prog جمعه 20 شهریور 1405 11:43
    It’s a 2024 Geely Coolray, and I need to correct the mileage. The panel looks like this: First, remove the instrument panel. To do this, pull the visor up with one sharp movement, unscrew the 12 screws, and then remove the panel. The rear panel cover is secured with clips and 4 screws. EEPROM chip which contains the...
  • Read Land rover A2C83377600 Airbag with Xhorse Multi Prog پنج‌شنبه 19 شهریور 1405 11:52
    The Land rover airbag SRS Continental control unit is A2C83377600 AH22-14D374-AH. It does not have an external EEPROM, so you will have to read the processor itself. Continental A2C83377600 AH22-14D374-AH The module was read using the Xhorse multi prog programmer, which has a convenient connection diagram without...
  • VVDI Key Tool Plus Program 2022 Volvo XC60 All Keys Lost سه‌شنبه 17 شهریور 1405 11:34
    Program 2022 Volvo XC60 all keys lost with Xhorse VVDI Key Tool Plus successfully. Decode lock with Lishi auto pick. Remove CEM module under the instrument on the driver’s side. Disassemble the CEM module and read data with key tool plus. Connect 6 wires on the CEM circuit board. Also requires soldering a 100 ohm...
  • Will Xhorse Multi Prog Clone PSA SID803 ECU دوشنبه 16 شهریور 1405 12:40
    Question: ​I have a Citroën C4 2.0 HDI with Siemens SID803 ECU (not SID803A), and in the Xhorse Multi-PROG software, this specific ECU is only listed under OBD mode for reading MAPS. ​Since this is only a partial read, is it safe to flash an EGR, Stage1, file via OBD with this tool? Solution: OBD mode you can just...
  • Xhorse Multi Prog Current Firmware is Lower than Supported Version Solution پنج‌شنبه 12 شهریور 1405 12:58
    Problem: Had a problem updating Xhorse Multi Prog programmer. It said the current firmware version is lower than the minimum supported version V1.4.9. Tried to update the firmware but failed. Any solution? Solution: Do a forced update. Press and hold the RST button while turning on the power, and keep holding it for...
  • How to Connect Xhorse BMW BDC3 Clip Adapter with VVDI Mini Key Tool چهارشنبه 11 شهریور 1405 11:23
    Question: Will Xhorse VVDI Mini Key Tool clone BMW G series BDC3 key? How is the wiring done with the XDNPBDGL adapter ? VVDI mini key tool does support BMW non-encrypted BDC3/BCP key cloning. Mini key tool is compatible with XDNP111 BDC3 clip adapter. How to hook the adapter to it? It has the same port that wired...
  • VVDISHOP 14th Anniversary Sale up to 50% OFF سه‌شنبه 10 شهریور 1405 12:41
    VVDISHOP is rolling out our 14th anniversary flash sale promotion. To our valued customers – thank you for 14 incredible years. Your trust and support have been the driving force behind everything we do. We couldn’t have made it this far without you. This promotion is our way of saying ‘thank you’ from the bottom of...
  • Generate Fiat 500X MQB Key with Xhorse XT1M or XT57B Chip دوشنبه 9 شهریور 1405 12:27
    Problem: Tried to add a spare Fiat 500x blade key with Xhorse vvdi key tool plus using XT1M MQB chip . Process went completely fine until key add part. Original key of course successfully added to the car but XT1M chip says “no dealer key recognized”, even though the generation went fine, tried 3 different...