How to Cut Audi HU66 Key by Xhorse Dolphin XP005L and Key Reader

 I’m going to show how to use Xhorse Dolphin XP005L + Key Reader to cut a new Audi A6 HU66 key. Firstly you should have a working key for reading key bitting codes. Let’s get to start.

Step1. Read Bitting Codes

1. Turn on Dolphin II, it’ll power-on self-test.
2. Use Xhorse app for Bluetooth connection.
3. Insert the key into XDKR00GL Key Reader for optical reading.

Optical identification >> Audi >> A6 >> HU66 >> OK >> Identification >> Identification

Identification successful.

Key biting codes: 11334242

Press “To cut” to complete.

Step2. Cut Key

*It’s suggested to do height calibration before cutting.

Device information >> Height calibration >> Start

Put the key to be cut on M5 clamp side B position 0, lock the knob.

Close the protective cover to prevent the cutting iron filings from flying around.

Cutting key >> Continue

Dolphin XP005L machine starts cutting…

Clean up debris after cutting completed.

Turn the key over and continue to cut the other side.

Continue cutting…

Wait until finished.

Take out the key to check cutting effect, it’s same as the working key.

It can successfully open lock as well.

Well done.

www.vvdishop.com

Generate Toyota Tacoma 2019 Key via Xhorse XM38

 Toyota Tacoma 2019 (8A proximity) all keys lost programming using Xhorse Toyota XSTO01EN XM38 smart key.

1. Generate XM38 and correct frequency with xhorse vvdi key tool max.

2. Programming all keys lost with xtool x100 pad2 pro.

if you don’t change the frequencies the presence doesn’t work. Just turn it on by moving the key closer to the start button.

VVDI Key Tool Plus Read Audi A6 J518 ELV EEPROM and Flash

 How to read Audi A6 J518 ELV MCU 3L40K with xhorse vvdi key tool plus?

The module is damaged, the car does not want to start, error 00288 steering column lock actuator (n360): defective
The processor is read, the information will be written to another module and can be used to make a new key if all keys are lost.

Select Prog->IMMO->Audi->J518(-2010)(1L59W/3L40K)

Check wiring diagram

Connect J518 module with vvdi key tool plus mcu cable following the wiring diagram

Read and save eeprom

Read and save Flash data

www.vvdishop.com

Xhorse Dolphin XP005 Firmware 1.7.4 Solved VA6 Issue

 Some users reported that Xhorse Dolphin XP005/XP005L had bugs when cutting VA2/VA6 key blanks in the last update.

The problem was solved by the last update. V1.7.4 came out and fix the va6 issue. 
Update the firmware to 1.7.4 or Dolphin machine and update also the Xhorse app.

Feedback:

Just cut a VA6 I decoded the key Q-H then cut as normal.
so I tried again with the same key but this time I noticed a new item in the menu just before you click cut (See Photo)

I ticked this and cut the key again (you have to tick it on both cuts)

Put it in the lock and it worked.
on the 2nd cut it took a fraction more off one side and the back end of the key

But it worked in the lock.

ODIS V23 Works Ok with Xhorse MVCI Pro

 Xhorse MVCI Pro J2534 was tested working with VW Audi Skoda Seat ODIS-S service software V23 and ODIS-E Engineer software V17.

Software version: ODIS-S V23.0.1/ ODIS-E V17.01

License: Included License Standalone and License for all brand

Compatible device: Xhorse MVCI Pro (and other passthru devices VXDIAG VCX SE 6154, openport 2, vnci 6154a, godiag j2534 etc)

Operating system: Win10 or later O/S, RAM>4G. Win7 is not supported since this version.

Language: Multi-language

Both software can be downloaded for free. But not include keygen.

If need activation, contact

Skype:VVDIfactory.com
Email:[e-mail]
WHATSAPP:+86?13559259147

We will send software in U disk format which contains 1 time free activation for both ODIS-S and ODIS-E software.

Tested models by far:

Model	VIN	ECU Type	Protocol	ODIS S 11	ODIS S 23.0.1	ODIS E 17.01
2007 AUDI A6	LFV3A24F273054910	MED9.1	KWP2000	√	√	√
2005 VWCaddy	LFVBC32K053000112	EDC16U1	KWP2000	√	√	√
2007 VW Passat	WVWVU73CX7E001193		CAN BUS	√	√	√
2017 VW Passat	LFV3A23C5H3071340	SIMOS 18.3	CAN BUS	√	√	√
2008 Audi A6	WAUDH74F98N068455	SIMOS 6.22A	CAN BUS	√	√	√
2008 VW Passat	LFV3A23C583003748	MED17.5	CAN BUS	√	MVCI Pro supports full system diagnostics (other J2534 only OBD scan)	√
2008 AUDI A6	LFV5A24F783014364	SIMOS 8.10	CAN BUS	X	X	√

Steps to Install ODIS-S/ODIS-E

1.Install Setup

2.Activate software

3. Install PostSetup

4. Install driver

5. Run software

MVCI Pro J2534 driver is included in the U disk.

www.vvdishop.com