Program FIAT 500 2008-2017 ID46 Key with VVDI Key Tool Max Pro

Today I’m gonna show how to add a new smart key for 2009 FIAT500 first version with Xhorse VVDI Key Tool Max PRO by OBD.

Turn ignition on.

Connect VVDI Key Tool Max PRO to car OBD port.

Immo programming >> FIAT >> Select by area >> European area >> 500 >> Flip-key(2008-2017) >> IMMO system(DELPHI 93C86_ID46) >> Start programming >> Type 1(93C86) >> Display immo information(PIN, Key ID)

Here we can check the password: 27665

Press “Make dealer key”

Please put the key or blank 46 chip in the sensing coil of the Key Tool Max PRO and keep it still, because some non-original key position will be different.

Press OK.

Generating dealer key, please wait…

Generate dealer key successfully.

Press “Key programming”.

All keys that can start the vehicle must be programmed, keys that are not programmed will be scrapped(cannot be programmed again).

The new key to be programmed must be a dealer key!

Press Yes to continue.

Please enter a 5-digit security code: 27665

Here Key Tool Max PRO will automatically enter it.

Switch ignition on.

Current key number: 2

Insert the wanted programming key, switch ignition on.

Programmed successfully.

Press Yes to program next one.

Remove the current key, then insert the key to be matched and turn on ignition!

Programmed successfully.

Press No to continue.

Turn the ignition off.

Switch ignition on.

Key program function ends.

Current number of keys: 2

Please make sure whether the key function is normal!

Test the new keys, both can start the car and remote work OK.

Done.

www.vvdishop.com

Read MC68HC08AZ32 with UPA USB or Xhorse Multi Prog

 It is a processor MC68HC08AZ32. Try to read the processor from Security Byte using two programmers, Xhorse Multi Prog and UPA-USB S.

See which one is better at this processor.

UPA S:

Processor blocked from reading, read each cell from EEPROM area as AD

Multi Prog:

Everything works better when connected to a computer.

Attention!!!
If you do not have a special password to read data from the processor, use Multi-PROG, which automatically finds the Security Byte in the MC68HC08AZ32 processor.

www.vvdishop.com

VVDI Key Tool Plus Program 2016 VW Caddy ID48 All Keys Lost

User feedback: Xhorse VVDI Key Tool Plus program VW Caddy 2016 key successfully.

5 minutes from start to finish.

• Read and save eeprom data
• Read and save immo data
• Reset instrument, clear DTC
• Generate dealer key
• Learn key

System: IMMO 4.5

Key type: ID48 96bit

Its crossover system, system 4 UDS with key mqb.

Remote add 09 channel after immo programing.

Caddy and transporter have mqb48 with old 202ad remote. You can code remote with chip or separately. The newer models – 202BH you must code it with chip learning – like golf7 etc.

Ford Transit 2014-2018 BCM Pinout to VVDI Prog

Here is the Ford Transit 2014-2018 BCM body control unit pinout to Xhorse VVDI Prog.

In case some followed the connections in VVDI images but got a frequency error when trying to read the chip.

Processor: D70F3637

How to Cut Mini Cooper HU92R Key with Xhorse Dolphin XP005L?

 Today I’m gonna cut a 2004 Mini Cooper HU92R mechanical key with Xhorse Dolphin II by bitting. Before that, you should get the bitting codes. Since I’ve used LISHI HU92 to decode the lock, let’s go straightly to cut the key.

Cut by bitting >> HU92R >> 820*4100 8 bitting, cut depth 1.25mm >> OK

Follow the prompt to install key blank.

Tip align 2nd position on M5 clamp side B.

Input bitting codes on screen: 3122 3443

Cut key >> Cut

The Dolphin 2 machine will start to cut automatically…

Just wait until it finished.
Then flip over to cut the other side.

Take out the key when key cutting was completed.

It can work perfectly.

Real quick and easy job.

www.vvdishop.com