How-to guide: Xhorse VVDI Prog read Ford airbag SRS control unit GN15-14B321-KB to clear airbag crash.
Model: Ford Ecosport
Airbag part number: GN15-14B321-KB
Memory type is Infineon TriCore SAK-TC222S-16F.
Device to read: Xhorse vvdi prog or multi prog
Connect airbag module with vvdi prog via mcu3 reflash cable.
In vvdi prog, select MCU- INFINEON TC2XXX- TC22X-16F (JTAG)
Read DFLASH and Pflash data respectively.
Here is the Ford Transit 2014-2018 BCM body control unit pinout to Xhorse VVDI Prog.
In case some followed the connections in VVDI images but got a frequency error when trying to read the chip.
Processor: D70F3637
Problem:
Tried to read VAG MQB D70F3532 cluster with xhorse vvdi prog and MQB solder free adapter, read works, write does not. Software says write error (00). Any solution?
Solution:
1.Make sure your vvdi prog software is up-to-date.
2. If reads ok, write does not, use a hot gun to heat the chip with a temperature 200 degrees (Do not exceed 350 degrees).
3. If still fails, then use cut pin method to read/write this cluster.
The answer is yes. To successfully read old Motorola HC11 series chips, ETL programmer was a must before. But now, it’s difficult to find one on market. This may cause trouble when reading old Land Rover with HC11 chips. Fortunately, after engineer’s correction and upgrade, Xhorse VVDI PROG is able to read & write HC11 series chips!
How to read MOTO HC11 chips with VVDI PROG?
For example, the bitmask on CPU is 0G10V. We can get its standard code MC68HC11P2 via MOTO Bitmask List.
Brand: Motorola MC68HC(7)11 Series
Chip: MC68HC11P2
This function can help locksmiths to solve data reading & writing problems for some old cars. No more to buy additional programmers.
Here comes the 2 working solutions to common Xhorse Audi BCM2 adapter data reading and writing problems using VVDI Key Tool Plus or VVDI Prog.
Read DATA1 success, reading DATA2 got “unknown error: 130400.1” error when progress goes to 2% it says “the data reading failed” with vvdi key tool plus.
How to fix?
Proceed with caution when you get “unknown error: 130400.1”. just check if the wiring or the adapter has stable contact and if the external power supply is stable, again try 1-2 data reading until successfully (do not read DATA1 again during this process, or do not try to unlock and try to install back to the car). After the data reading is normal, there will be no other problems, and then you can install back to the car.
Read more: How to connect/use Audi BCM2 adapter with vvdi key tool plus?
Read both DATA1 and DATA2 data successfully, the IMMO data and service mode data are generated successfully. However, vvdi prog reports an error when writing service mode data to 99%, after trying again, the system pops up that the erasure failed. After that try to read DATA1 again, it will not be able to read.
How to fix?
If you have the same problem that the DATA1 and DATA2 data is read successfully, also the service mode data is saved, then just select the unlock option to unlock the CPU.
Wait until the system says that the unlock is successful.
At this time, choose the service mode, then import and write the service data.
After the data is written successfully, just install back to the Audi car, and the vehicle can work, you do not need to do any processing.
Read more: How to connect/use Audi BCM2 adapter with vvdi2+ vvdiprog?
Audi encrypted BCM adapter tech support: www.vvdishop.com