How to Fix Xhorse Dolphin XP005 Shows M5 Clamp

 Problem:

Why my xhorse app shows my xhorse dolphin xp005 (DOLPHIN 1) to use the dolphin 2 clamp? There was a new app update. It’s happening on my phone. Everything says m5 clamp but I have dolphin 1.

Solution:

Currently, M5 clamp is not yet compatible with the dolphin xp005 key cutting machine (wait for feature firmware update). It is for Condor II and Dolphin II.

If xhorse app asks to use M5 fixture after upgrade, go to Device information at bottom right-then Cutting setting then change clamp to M1/M2.

Xhorse Dolphin XP005 Cannot Fully Charged Solution

Some of xhorse dolphin xp005 key cutting machine users reports that the battery has shown fully charged. 3 bars is the most it gets. How to get rid of this?

Solution:

It needs an update. Update it and it settled, update it and ready you have to do it with the PC.

Update the firmware to fix the problem and go back to 4 bars.

Follow guide below to update your dolphin xp-005

How to Update Xhorse Dolphin XP005 Software and Install Driver?

If still the same won’t go back to 4 bars, check if dolphin xp005 will cut 3-5 keys by charging overnight, if yes, the battery is good. It does not matter.

VW Golf 6 MK6 Key Programming by Xhorse VVDI2

 VW Golf 6 MK6 has a working key and need to add a new spare key using xhorse vvdi2 key programmer. Check instructions below.

Procedure:

Connect by obd2 on car.
Ignition is on with a working key.

Run VVDI2 software, select VW->Diag
VVDI2 detects instrument type TFT color display NEC 24C64 (-2012)
Read EEPROM/Flash->Read EEPROM

Switch on with the working key before press OK

But it says non-standard login failed
This time we choose manually
Go to Key Learn->4th Immobilizer system VW/Skoda/Seat->Instrument with NEC+24C64
Read EEPROM/Flash->Read EEPROM->Login Method 2

Reading data
Reading data success

Save eeprom data
Then Read Immo Data->Login Method 2
Read Immo data success and save data

Select Make Dealer Key and Login Method 2
Put new key into vvdi2 vag coil

Prepare VW normal dealer key and press NEXT

Make dealer key ok and locked
Then Add key

You should backup eeprom and immo data before learn key.
Select Learn key with security code from immo data, put key into the ignition switch.

Load immo data and input 2 keys to be learned
Select No this car does not have keyless.

Insert the dealer key into car and switch on for at least 2 seconds. The time for change key should less than 5 seconds.
Wait till appear 1-2 on cluster, then ignition on with second key.
Now 2-2, then ok
All keys were successfully learned.
Reset instrument.

Done.

www.vvdishop.com

Xhorse Garage Remote Frequency Different from Original Solution

There are many different brands of garage remotes with different frequencies on the market. If you find that the copied function is unavailable or the remote control distance is too short, it’s probably due to the Xhorse Garage Remote frequency is different from the original remote. To solve these problems, you need to set the same frequency as the original remote.

There are 2 ways to set same frequency as original remote: set frequency on garage remote(without device) & set frequency by VVDI key tool device.

Method1. Set Frequency on Garage Remote

1. Enter the set-frequency mode.

Press and hold the Lock and Pause buttons simultaneously, you can see the LED light turns on. When the light turns off, release the buttons.

2. Set frequency.

Press the Up button. Different press times correspond to different frequency points. For example, if we press it twice, the LED will flash twice, which means it is set as the second frequency point.

3. Double check frequency

After setting frequency successfully, release all buttons. Wait 5 seconds, the remote LED light will flash again for you to confirm which frequency point it’s at right now. The number of flashes corresponds to the frequency set.

You can refer to the frequency reference table:

4. Exit set-frequency mode

After the remote LED light stops flashing, press the Lock and Pause buttons immediately. When the LED light turns on and then off, release the buttons.

Method2. Set Frequency by VVDI Key Tool

If the frequency you need is not in the frequency reference table, you can use VVDI Key Tool series device to set frequency at random point. Such as Key Tool, Mini Key Tool, Key Tool Max, Key Tool Max PRO or Key Tool Plus.

Here we take Mini Key Tool as an example to set the frequency of Masker, and the operation steps are as follows:

1. Connect to the device.

Remove the Xhorse logo and loosen the screw. Open key shell to take out the PCB board inside. After pairing Mini Key Tool to the phone via Bluetooth, we connect the device to Masker with a programming cable.

2. Generate copy program.

Garage remote >> AA_Xhorse_copy program >> Update copy remote V108 support edit frequency >> Generate

It is worth mentioning that Masker adds an interface to support wired generating, which is more stable than wireless generation. So we don’t need to read the tips for wireless generating. Just tap “OK” to start the generating.

3. Customize frequency

Special function >> VVDI remote function >> Garage door key customization >> Read >> Modify

First we read the information of the Masker. Then we can see the current frequency value in the table. We just need to tap the frequency value, enter any value you want. Tap “Settings” to modify the frequency.

Now we successfully get a remote that sets our required frequency.

www.vvdishop.com

Read VW RCD510 Radio NEC and EEPROM by Xhorse VVDI Prog

 How to read Nec V850 D70F3356 Processor & 95128 Eeprom with xhorse vvdi prog to get VOLKSWAGEN 5k0035190a Bosch RCD510 Entry Radio Code.

Step 1:

Read Nec V850 D70F3356

Connect Nec V850 D70F3356 processor with vvdi prog via mcu3 adapter

In vvdi prog software, select MCU-Renesas V850- D70F3356 and save data

Step 2:

Read eeprom

Connect 95128 mcu with vvdi prog via clip adapter.

With clip adapter you don’t need to unsolder the chip from the board.

Select EEPROM-ST-M95128

Read and save eeprom data

Code location in eeprom – line 000AE0 ( 8А 37 8D A4 ). Code = A7D4 x or XXXX. To calculate XXXX – need a dump NEC.

Open dump,  try the 0xAE0 to 0xD00 fill to 0xFF method, and get the data after “Power on”.

There are also 3rd party radio code calculators available.

www.vvdishop.com