VVDI Key Tool Plus ECU ISM Gearbox Pinouts

Question:

I want to read engine ME9.7 ECU with xhorse vvdi key tool plus but the device does not show a wiring diagram. Where to find engine, gearbox and ISM wiring to key tool plus?

Here are some of the wiring diagram to key tool plus.

CR3.xx

CR4.xx

CR5

CR6

CR60.xx

CRD.11

CRD2.xx

ME9.7

MED17.7.x

7G Gearbox

ISM

SIM4LE

SIM4LKE

SIM266

SIM271DE2.0

SIM271KE2.0

Keep updating…

https://www.vvdishop.com/service/vvdi-key-tool-plus-benz-ecu-wiring-diagram.html

How to Cut Audi HU66 Key by Xhorse Dolphin XP005L and Key Reader

 I’m going to show how to use Xhorse Dolphin XP005L + Key Reader to cut a new Audi A6 HU66 key. Firstly you should have a working key for reading key bitting codes. Let’s get to start.

Step1. Read Bitting Codes

1. Turn on Dolphin II, it’ll power-on self-test.
2. Use Xhorse app for Bluetooth connection.
3. Insert the key into XDKR00GL Key Reader for optical reading.

Optical identification >> Audi >> A6 >> HU66 >> OK >> Identification >> Identification

Identification successful.

Key biting codes: 11334242

Press “To cut” to complete.

Step2. Cut Key

*It’s suggested to do height calibration before cutting.

Device information >> Height calibration >> Start

Put the key to be cut on M5 clamp side B position 0, lock the knob.

Close the protective cover to prevent the cutting iron filings from flying around.

Cutting key >> Continue

Dolphin XP005L machine starts cutting…

Clean up debris after cutting completed.

Turn the key over and continue to cut the other side.

Continue cutting…

Wait until finished.

Take out the key to check cutting effect, it’s same as the working key.

It can successfully open lock as well.

Well done.

www.vvdishop.com

Generate Toyota Tacoma 2019 Key via Xhorse XM38

 Toyota Tacoma 2019 (8A proximity) all keys lost programming using Xhorse Toyota XSTO01EN XM38 smart key.

1. Generate XM38 and correct frequency with xhorse vvdi key tool max.

2. Programming all keys lost with xtool x100 pad2 pro.

if you don’t change the frequencies the presence doesn’t work. Just turn it on by moving the key closer to the start button.

VVDI Key Tool Plus Read Audi A6 J518 ELV EEPROM and Flash

 How to read Audi A6 J518 ELV MCU 3L40K with xhorse vvdi key tool plus?

The module is damaged, the car does not want to start, error 00288 steering column lock actuator (n360): defective
The processor is read, the information will be written to another module and can be used to make a new key if all keys are lost.

Select Prog->IMMO->Audi->J518(-2010)(1L59W/3L40K)

Check wiring diagram

Connect J518 module with vvdi key tool plus mcu cable following the wiring diagram

Read and save eeprom

Read and save Flash data

www.vvdishop.com

Xhorse Dolphin XP005 Firmware 1.7.4 Solved VA6 Issue

 Some users reported that Xhorse Dolphin XP005/XP005L had bugs when cutting VA2/VA6 key blanks in the last update.

The problem was solved by the last update. V1.7.4 came out and fix the va6 issue. 
Update the firmware to 1.7.4 or Dolphin machine and update also the Xhorse app.

Feedback:

Just cut a VA6 I decoded the key Q-H then cut as normal.
so I tried again with the same key but this time I noticed a new item in the menu just before you click cut (See Photo)

I ticked this and cut the key again (you have to tick it on both cuts)

Put it in the lock and it worked.
on the 2nd cut it took a fraction more off one side and the back end of the key

But it worked in the lock.