Suzuki Bosch ME17.9.64 ecu is supported by xhorse multi prog. It will read and write this ecu on bench mode.
It works but the pinout is incorrect on multi prog.
In the Multi prog program. There is a bosch part number lookup. Use the numbers of the ECM and narrow your search. Then use that information to look up the ECU pinout online.
According to our customer’s feedback. the pcm flash/pcmtuner wiring diagram works no issue.
www.vvdishop.com
We have shown how to add an MLB key with VVDI MLB Tool and VVDI Key Tool Plus (check instructions). Here we will show how to use the MLB-Tool with VVDI2 to add key Audi MLB.
Procedure:
Follow the diagram to solder wires to vvdi mlb tool.
Download and install MLB tool software.
Connect MLB Tool with computer.
Put the key on the identification area.
Run VVDI MLB Tool software.
Identify key
Key is locked and initialized.
Select Collect Key Data
Select the method for collect key data as needed.
No OEM key here means using the original key.
Use the OEM key here means using VVDI dedicated MLB key. Use VVDI MLB does not deduct points.
Data calculation completed.
Press OK for verification.
Data verification is successful.
The data can be used to make dealer key.
Select Make dealer key.
Then we learn key with VVDI2 programmer.
Turn on the ignition switch
Connect VVDI2 with vehicle and PC
Place the original key in the induction area.
Run VVDI2 software and select correspoding vehicle software, i.e Audi
Select Key Learn->MLB Immobilizer System
Read vehicle information and press Key Learning
Both keys need to be learned.
Upload IMMO data read by Xhorse VVDI MLB Tool
Start key learning.
Learn 1st key success.
Place new key in the induction area
Learn 2nd key successfully.
All keys are successfully learned now.
Test the key function.
Smart function working as expected
One touch start ok, remote control, and keyless all working
https://www.vvdishop.com/service/how-to-use-vvdi-mlb-tool-with-vvdi2-to-add-mlb-key.html
How does Xhorse Multi Prog work on GM ACdelco modules? Good/Bad?
Xhorse Multi Prog support following GM Delco ECMs:
Delco E38
Delco E37
Delco E92
Delco E39
Delco E39A
Delco E67
Delco E82
Delco E80
Delco E83B
Delco E78
Delco E98
Multi-prog read these ECMs via bench and boot mode.
Our customers have read delco e83, e39, e98. Reading flash no issues on bench.
Boot mode will ask for a 16-digit password (shadow password), multiprog cannot read the password.
For example, when clone Delco E39/E98 ECMs, multi prog asks for 16-digit password. You can read password with obdstar or I/O terminal, then try reading with multiprog to test and confirm.
2017 Pathfinder, add-key with Autel IM508. It’s not taking any of the keys in, even their original key.
No DTC codes until after a few shots, now flagging B2198.
UPDATED:
My Xhorse VVDI Key Tool Key Max Pro came to the rescue.
It’s saved my ass on several Nissans that my Autel wouldn’t do.
Popped right in with it, after running the programming process on my Key tool max pro a second time. First time, the remotes took, but not the chips. Second programming run with the Key tool max pro, the chip programmed in. Not the first time my 508 failed me, either. The code went away after programming with the Xhorse tool.
www.vvdishop.com
Question:
How do you duplicate emergency key for 2021 Toyota Highlander TOY51 SINGLE SIDE with the newer version of Xhorse Dolphin XP005 with M5 clamp? Probe does not detect key, clamp seems too low.
Here is the clue:
You cut it on the wrong side.
You need to use the correct profile use the TOY40 one sided blade for emergency blade and it will work.
You cut the key on side A, not side B, the spacer is for condor, not dolphin. The double sided version is cut on side B.
You do not need a spacer with the dolphin, that’s for the Xhorse condor.
Select the correct key and it cuts perfectly every single time, no need to do anything special.
Go under TOY40 emergency key. New dolphin doesn’t use spacer.