2017 Pathfinder, add-key with Autel IM508. It’s not taking any of the keys in, even their original key.
No DTC codes until after a few shots, now flagging B2198.
UPDATED:
My Xhorse VVDI Key Tool Key Max Pro came to the rescue.
It’s saved my ass on several Nissans that my Autel wouldn’t do.
Popped right in with it, after running the programming process on my Key tool max pro a second time. First time, the remotes took, but not the chips. Second programming run with the Key tool max pro, the chip programmed in. Not the first time my 508 failed me, either. The code went away after programming with the Xhorse tool.
www.vvdishop.com
Question:
How do you duplicate emergency key for 2021 Toyota Highlander TOY51 SINGLE SIDE with the newer version of Xhorse Dolphin XP005 with M5 clamp? Probe does not detect key, clamp seems too low.
Here is the clue:
You cut it on the wrong side.
You need to use the correct profile use the TOY40 one sided blade for emergency blade and it will work.
You cut the key on side A, not side B, the spacer is for condor, not dolphin. The double sided version is cut on side B.
You do not need a spacer with the dolphin, that’s for the Xhorse condor.
Select the correct key and it cuts perfectly every single time, no need to do anything special.
Go under TOY40 emergency key. New dolphin doesn’t use spacer.
Today I’m gonna use Xhorse Multi-Prog Programmer to read Opel AcDelco E87 emulated eeprom for a test. Includes how to read, extract, import the emulated eeprom and do mileage adjustment.
Connect device& ECU according to wiring diagram on bench.
Open Multi-Prog software,
Read >> Yes, read emulated EEPROM
Reading data, please wait…
Data read successfully.
Save emulated eeprom to file? Yes
The operation was successful.
Extracted and saved the emulated eeprom.
Load emulated eeprom? Yes, selected the saved flash file.
Now we can get the PIN code & mileage.
Mileage is 121408.2976km
We can also modify its mileage:
KM >> Enter new value: 40000
The mileage has been changed to 400000km.
Click “EE-OUT”.
Extracts emulated eeprom from Flash.
Load INT-FLASH file? Yes, selected the original flash file.
The operation was successful.
Extracted and saved the emulated eeprom file.
Load emulated eeprom? Yes, selected the emulated eeprom file.
Click “EE-IN”.
Imports emulated eeprom to Flash.
Load the emulated eeprom? Yes, selected the emulated eeprom file.
The operation was successful.
Save the modified file? Yes
The operation was successful.
Load new FLASH? Yes, selected the new emulated eeprom file.
www.vvdishop.com
Some users reported that they have problems updating vvdi mini obd tool firmware and sync device.
If the version is lower than 1.5.0, try several times, change PC or network, if all failed, device information is missing. Need to send back for repair.
If the version is 2.1.50, disassemble the device, replace a new battery, update firmware and sync device again.
Sync device again after replacing battery. Then update firmware via Upgrade kit again.
Follow steps below to replace battery.
One of our customers reported that his Xhorse Dolphin XP008 manual key cutting machine sounds weird when duplicating key.
Here is the possible solution from Xhorse engineer.
1.Unscrew these two screws and take off the belt.
2. Unscrew 5 screws on the shell
3. Unscrew the top screw in this hole.
4. Unscrew the cutter head and you can take out the bearing
5. You can apply some glue on these two bearings, it must be a thin layer.
Install machine again, then try to cut key.