ابزار Xhorse VVDI

Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزار

ابزار Xhorse VVDI

Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزار

عناوین یادداشت‌ها

  • Xhorse VVDI2 7.3.6 Adds VAG MLB Key Learning دوشنبه 13 فروردین 1403 08:51
    Xhorse VVDI2 key programmer released new software version V7.3.6 on March 31st, 2024. *** 2024-03-31 *** Require firmware V7.3.5 ************************************************************************ ===== VAG V7.3.6 ===== 1. Support MLB immobilizer key learning-Require VVDI-MLB TOOL 2. Support Fix dashboard data...
  • How to Get VW NEC35xx CS PIN with VVDI Key Tool Plus No Soldering جمعه 10 فروردین 1403 12:06
    How to get the CS and PIN code of Volkswagen Skoda white meter petrol car without lifting the pin or cutting the track? Following we’re gonna to do it with Xhorse VVDI Key Tool Plus . In this way, we can read the meter data for mileage adjustment. If it’s not working, we can also read and write this data directly for...
  • How to Solve Xhorse Multi Prog Failed to Update Firmware پنج‌شنبه 9 فروردین 1403 11:48
    Problem: Failed to update xhorse multi prog firmware (Jump recovery error). The current firmware is 1.1.0. Also failed to sync device. Any solution? Solution: Press and hold the Reset button on the main unit before powering on, and hold it for 5 seconds after powering on. Try to force firmware upgrade.
  • How to Check if Xhorse Condor II Battery is Good or Not چهارشنبه 8 فروردین 1403 11:42
    If you cannot turn on Xhorse Condor XC-Mini, Condor XC Mini Plus or Condor II key cutting machine, you may need to test the 24v voltage output of the battery to check if needs a battery replacement. Follow this way to test Xhorse Condor battery: 1.Remove these screws to take out the battery. 2.Connect 220V power...
  • VVDI Prog and VVDI2 2010 Ford Transit All Keys Lost سه‌شنبه 7 فروردین 1403 11:26
    2010 Ford Transit Mk7 all keys lost and active Cat1 factory alarm. Key learning cannot be carried out by normal OBD operation with alarm active as key learning by OBD is blocked. Removed BCM, read key data (chip MC9S12DG256) directly from the module using xhorse vvdi prog on the bench, added a new key on the bench...
  • Update VVDI Mini OBD Tool Firmware to 1.5.0 دوشنبه 6 فروردین 1403 11:39
    If Xhorse VVDI Mini OBD tool asks to update the firmware to V1.5.0 or above using the Xhorse Upgrade kit, here are the upgrade tips. Update is done via Upgrade kit from PC (not phone). First of all, update Xhorse upgrade kit to 1.8.2 online or directly install Upgrade kit 1.8.2. Select device as MiniOBD1 and version...
  • Program Audi BCM2 Key with Xhorse Multi Prog and VVDI2 جمعه 3 فروردین 1403 09:24
    Here we’re taking about how to read VW/Audi BCM2 module with Xhorse Multi-Prog Programmer without soldering. The Audi BCM2 Solder Free Adapter & VVDI2 will also be required. Open Multi-Prog software, Device >> Selected BCM2 model: LOCK_BCM2-2(ADAPTER)(AUDI->AUDI) >> OK >> Details >>...
  • Xhorse Multi Prog Update 9DF SID209 DCM7.1A پنج‌شنبه 2 فروردین 1403 08:35
    Xhorse Multi Prog released new database version on March 18th, 2024. Software Version 1.1.3.0 Firmware version V1.1.8 Database V12 2024-03-18 11:30:10 * Some options wiring diagrams increase pull-up resistance * Added chip id identification for some options * Added the boot wiring diagram of FCA_MARELLI_9DF in ECU *...
  • Xhorse Dolphin XP005L No M3 Clamp Cutting Setting? چهارشنبه 1 فروردین 1403 11:19
    Question: I would like to know how to duplicate a sx9 key with Xhorse Dolphin II . I can’t find the M3 clamp in the machine menu. Answer: Don’t need to choose M3 clamp option in settings. Direct replace M3 clamp when cutting sx9 key (or other tibbe keys) Read also: How to Tighten Xhorse M3 Clamp for Condor/Dolphin?
  • Xhorse VVDI Prog Ford Transit BCM BK2T Pinout سه‌شنبه 29 اسفند 1402 09:19
    Here comes the Ford Transit BCM BK2T-14B476 Nec70F3637 pinout to Xhorse VVDI Prog . this is vvdi prog connetion diagram
  • How to Solve Xhorse B5 Super Remote Error Convert Failed? دوشنبه 28 اسفند 1402 12:25
    Problem: Any idea why I failed to reset the Xhorse XEB510EN B5 Super Remote ? error convert failed. Solution: You don’t need to convert or reset B5 super remote. Just re-generate remote directly then program it. www.vvdishop.com
  • Xhorse Multi Prog Clear Peugeot 308 MED17.1 P0016 fault code جمعه 25 اسفند 1402 11:32
    This is a tutorial on how to remove 2010 Peugeot 308(1.6 petrol engine) P0016 fault code with Xhorse Multi-Prog Programmer. The check engine was on the dashboard, and the fault code was red with a diagnostic tester. In addition, we also need ECU Soft Service for modification. Step1. Read EEPROM & FLASH It’s a...
  • How to Enable Xhorse Dolphin II Developer Mode? پنج‌شنبه 24 اسفند 1402 15:08
    If your Xhorse dolphin xp005l (dolphin ii) key cutting machine does not bring new updates and whenever you update it stucks on screen, you may need to enter developer mode to update firmware. Here is the guide to enter developer mode. Go to System Press the question mark icon on the right top of the screen Press the...
  • Xhorse VVDI Prog BMW FRM Lost OBD Communication? چهارشنبه 23 اسفند 1402 11:22
    Problem: In this E series FRM XDT256 model, after making a copy of the EEPROM and FLASH with xhorse vvdi prog , I have a ‘Lost OBD communication’ error. Any solution? Solution: FRM Repair Method: Remove FRM, check data with VVDI Prog , if all data are blank (FF), then write data to the MCU. First disassemble the FRM...
  • VVDI Prog Renesas V850 D70F3366 Try Frequency Failed Solution سه‌شنبه 22 اسفند 1402 15:02
    Problem: When trying to read Renesas V850 D70F3366 MCU with xhorse vvdi prog , it failed to read and said error try freuqency failed. Solution: Soldering problem. Remove, solder the chip and read it (follow the wiring diagram). www.vvdishop.com
  • Read and Write VW Passat EDC17CP14 by Xhorse Multi Prog دوشنبه 21 اسفند 1402 09:21
    Xhorse Multi Prog will read and write VAG Bosch EDC17CP14 ECU on bench and boot mode. Here we read it on bench mode. Select VAG Passat Bosch EDC17CP14 Here we read it on bench. Check wiring diagram Connect ECU with multiprog via ecu adapter Read INT eeprom It takes 3min 13s to read eeprom. Then save data. Read INT...
  • Xhorse XM38 Failed to Copy 46 Copy Proximity پنج‌شنبه 17 اسفند 1402 14:21
    Problem: I’m using Xhorse XSFO02EN XM38 Smart Key and trying to copy the Peugeot ID46 keyless key, but error pops up, so please advise. Write failed, NOT support this chip. Solution: Xhorse SM38 universal smart keys can not be used to copy proximity. You need to generate xm38 remote then program to car with vvdi key...
  • How to Repair Benz W205 BMS with Xhorse VVDI prog سه‌شنبه 15 اسفند 1402 09:04
    This is the BMS (battery module) used on Mercedes C Class W205. The battery is out of power. So we need to repair the file using the xhorse vvdi prog programmer. Put some soldering paste on it. Use this hot air station to heat it until it reaches a certain temperature. Then take it off with tweezers. Be careful not to...
  • EDC16U1 Change KM and IMMO Off using Xhorse VVDI2 دوشنبه 14 اسفند 1402 13:26
    How-to: read EDC16U1 ECU CS, MAC code, change km and IMMO Off using Xhorse vvdi2 programmer. Run vvdi2 software Select VW program Go to Special Function-> Engine Control Unit Read memory data Detect type as EDC16U1 Read CS and MAC successfully Input KM you desired to change and press write KM Switch ignition OFF...
  • How to Use Xhorse Toyota BA 30-PIN Cable جمعه 11 اسفند 1402 11:53
    This is a tutorial to show how to use Xhorse Toyota BA Cable step by step. The cable can be used for 2022- Toyota BA models adding key and all keys lost. It can work with VVDI Key Tool Plus , Key Tool Max Pro & Mini OBD Tool( FT-OBD version). In this article, we’ll use the cable to read immo data and add a new key...
  • How to Solve Xhorse Dolphin XP005L Decode Error Code 2? پنج‌شنبه 10 اسفند 1402 11:26
    Problem: I did the first installation but my xhorse dolphin ii key cutter doesn’t decode the keys. Fiat Idea SIP22 blank. Solution: You didn’t put the key in the clamp correctly. Key needs to sit higher in clamp on top level. Re-adjust the key in the m5 clamp . The shoulder of the blade is your stop point at the jaw....
  • Xhorse Multi Prog Adds VAG MQB RH850 Dashboard چهارشنبه 9 اسفند 1402 11:58
    Xhorse Multi Prog programmer released new software version 1.1.2.0 on Feb, 26th, 2024. Database V11 2024-02-26 14:36:44 * MCU STM8S and STM8AF series wiring diagram update. * MQB dashboard options process optimization and wiring diagram update. * Repair NATS5-IMMO option in <IMMOBILIZER>-><NISSAN> + Add...
  • Xhorse Multi Prog Read Renault SID301 by BDM سه‌شنبه 8 اسفند 1402 11:30
    It is a Renault SID301 ECU from a Renault Megane 2. It was water damaged. Need to read it and copy to another ECU. This ECU is really cheap and don’t want to repair. We can read this ECU with Xhorse Multi Prog via BDM. Pinout is included in the multiprog documentation. Select Renault->SID301 Check wiring diagram...
  • How to Add BMW 2019 BDC Key with VVDI Key Tool Plus via OBD دوشنبه 7 اسفند 1402 11:54
    How-to: add a spare key to BMW Serie 2 gran tourer year 2019 F46 smart key with xhorse vvdi key tool plus via OBD. Select IMMO programming->BMW->Auto detect vehicle Detect type as FEM/DC Read key information Need unlock, the software is 080, it is safe to be done via OBD Select Unlock FEM/BDC system Support...
  • Xhorse Multi Prog Adapters List جمعه 4 اسفند 1402 11:44
    Xhorse has recently put out 4 sets of 2024 exclusive adapters for Xhorse Multi-Prog Programmer, which can read and write SOP44, TSOP48 flash chips or common 8-pin chip. With these adapters, engineers can accomplish data reading tasks more easily. Image Adapter Model Method Usage SOP44 & TSOP48 Adapter XDMP04GL...
  • Xhorse 8A AKL Adapter Was Bind to Other Device Error Solution پنج‌شنبه 3 اسفند 1402 11:32
    Problem: I need to program key for my Toyota RAV 4 2016, lost all keys using xhorse vvdi mini obd tool and 8A non-smart key adapter . But the app says the adapter was bound to other devices. Any solution? Solution: 8A adapter can only be bound to 1 xhorse device (key tool max pro, vvdi2, key tool plus or vvdi mini obd...
  • Xhorse VVDI Mini OBD Tool Program 2017 Grand Caravan All Keys Lost چهارشنبه 2 اسفند 1402 12:39
    How-to: program 2017 Dodge Grand Caravan All keys lost using the Xhorse VVDI Mini OBD Tool and mobile phone via OBD. Connect Mini obd tool with car via OBD connector Run Xhorse app on mobile phone Select IMMO Programming->Dodge->Select by area-> North America->Grand Caravan->2010-2020->Toothless...
  • VVDI Key Tool Max Clone 2021 Toyota Camry 8A Transponder سه‌شنبه 1 اسفند 1402 12:24
    How to clone 2021 Toyota Camry 8A Transponder using Xhorse vvdi key tool max . It is a 2021 Toyota Camry we are going to go ahead and clone the customer’s key. We’re going to go to transponder clone and reset transponder. We have inserted a vvdi super chip in our key. Make sure that you are connected to Wi-Fi hotspot...
  • Read and Write VW EDC16U34 with Xhorse Multi-Prog دوشنبه 30 بهمن 1402 09:12
    Xhorse Multi Prog programmer read and write VW Golf EDC16U34 ECU on bench successfully. Select All->olkswagen->VAG Bosch EDC16U34 (Volkswagen-Golf) Check wiring diagram Connect Multi prog with ECU via Multiprog ECU adapter Read EXT EEPROM Read EXT EEPROM and save It took 40 seconds to read the eeprom on the...
  • How to Bind Xhorse Multi Prog with VVDI Key Tool Plus? یکشنبه 29 بهمن 1402 11:57
    The benefit of combining Xhorse Multi Prog with VVDI Key Tool Plus : Multiprog has built-in MQB48 NEC35XX license, if combine multi-prog with vvdi key tool plus, you don’t need to purchase MQB48 license on key tool plus. Your key tool plus doesn’t need to activate MQB48 license, just load immo data read by multi prog...