VVDI Mini OBD Tool Program Toyota ID4D All Keys Lost

 This is 2003 Toyota with ID4D(67) chip all keys lost, so I’ll use Xhorse VVDI Key Tool Max + MINI OBD Tool to program 2 keys for this car. Total 2 steps: program IMMO via VVDI key tool then program remote manually. Without further ado, let’s get start.

Step1. Program IMMO

Plug MINI OBD Tool into OBD port, connect to VVDI Key Tool Max.

IMMO programming >> Toyota >> Classified by type >> Immo system >> Type 2(4D 67/68) >> Start execution >> Lost all key

Please switch ignition on.

Insert the key to be matched and open it to the ON position.

Click OK after completion.

Whether to continue to program next key? Yes

Insert the key to be matched and open it to the ON position.

Click OK after completion.

Insert the first key and switch the ignition switch quickly 5 times, click OK to continue.

Operated successfully!

If IMMO lights keep flashing, please remove the key, insert the key again and switch ignition switch quickly 5 times!

Test the two keys, both are working.

Step2. Program Remote

Following I’m gonna show how to manually program the remote.

1. First open the door then close, open the door and insert key into ignition twice without switching, close the door.
2. Open and close door again, leave door open and insert key once, close the door.
3. Open and close door again, leave door open and insert key without taking out, close the door then open again.
4. Now switch ignition on and off, then take out the key.
5. At this time, you can see the door flashing light is on. Press Lock & Unlock button, then press Lock button again.

Programming success.

Close and open door, then close again. Check the new remote, both can work.

Perfect done!

www.vvdishop.com

VVDI Key Tool Max Generate Toyota 8A Smart Key using Xhorse XM38

 How to generate 2018+ Toyota smart key using the xhorse vvdi key tool max and an xhorse XM38 universal smart key.

You will need the Toyota XM38 versions of their universal smart keys for this.
Make sure we do have a battery in the key.
Go ahead to Vehicle Remote and find Toyota.
Go down the list of all remotes to see if you can find the right FCC ID.

We have an option right there we see our FCC ID HYQ14FBA which should be the correct FCC ID for this vehicle.

We’ll take our remote with a battery in it. We’re going to insert the key on the antenna part of the key tool Max and then we’re going to hit Generate remote.

It’s programming the remote.

It’s putting me in a queue this is one of those you’ll have to have internet access for.

We’ll let it countdown now it’s generating the remote.

Generate remote successfully.

Many new Toyota keys cannot really be unlocked. Even refurbished ones that show up locked and unable to be programmed whereas these XM38 smart keys can be rewritten.

The reusability is a nice aspect of XM38.

www.vvdishop.com

Xhorse B5 Super Remote vs Regular Super Remote

 What’s the difference between Xhorse B5 Super Remote and regular super remotes?

B5 Super Remote comes with the new X27B chip is not the XT27A version that has more possibilities.

XT27B adds 47, 49, 4A and MQB chips types.

You will need B5 super remote to generate ID47, ID49 (.e 2018+ Ford ID49 proximity), ID4A (i.e Nissan 4A proximity) and MQB smart keys.

Ford Transit, Fiesta, F-150 etc ID49

Nissan Qashqai ID4A, Peugoet 3008 ID4A etc

MQB48 B5 Super remote

Check coverage in Xhorse App, if it ask to use B5 Super remote, buy XEB510EN remote instead.

www.vvdishop.com

Renault Megane 3 Pinout to Xhorse VVDI Prog

 Can you read eeprom/flash for Renault Megane 3 UCH (v850 processor) with xhorse vvdi prog?

vvdi prog read it with no problem.

check pinout to vvdiprog

For vvdi program, don’t select 4-Immobilizer->Renault->Megane UCH
But go direct to the mcu and select the right type and read.

Select 2-MCU->Renesas V850-> D70F3384 for example.

VVDI Key Tool Plus Read MQB D70F3537 with Xhorse MQB Adapter

 Xhorse MQB48 Solder Free Adapters are specially designed to provide an easier and safer solution to save automotive locksmiths from the intricate and annoying soldering, pin lifting and wire cutting work. Here we’ll walk you through how to read MQB D70F3537 data with the new adapter and Xhorse VVDI Key Tool Plus.

If the MQB48 solder-free adapter is not used, locksmiths may suffer from the complex operation and high risk of damage when reading VW MQB instrument immo data particularly BGA D70F3532/35/36/37. Possible problems are:

• Crystal oscillator frequency configuration failed.
• Difficult operations requiring experience and skills.
• Easy to cause damage and high risk of loss.
• May require the use of professional tool.

Procedure

Immo programming >> VW >> Select by type >> MQB instrument immo system >> Instrument-MQB48(VDO/JCI-NEC35xx lock) >> Start programming

Please read the disclaimer carefully, tap “OK”.

Please make sure Network connection is normal, click “OK”.

Programmer reads files >> Read NEC35xx chip >> Adapter method >> D70F3537

Here we can check the connection diagram.

Connection

Step1. Located the positioning points and connect the adapter to the board with reference to the points, connect and apply the clips.

Note: make sure the pins aim right at and keep good contact with the points. Otherwise, the following errors may occur:

• Crystal oscillator frequency configuration failed. There’s a problem with the contacts, please reinstall the adapter.
• Chip cracking failed.
• The contacts are loose.
• Continue reading repeatedly.

Step2. Connect XDNPM1GL MQB48-BGA Adapter to Key Tool Plus with DB15 cable.

Step3. Power it up using a power supply.

Read MQB48 IMMO

Read >> Continue

Reading success.

Save data file.

The immo data can be used to generate dealer key and for key learning.

Obtaining immo data >> Load and upload NEX35xx chip file read by Key Tool Plus>> Select the saved data

Is this instrument type is requires external EEPROM 95320 to be loaded: after 17 years of PASSAT(56D902861A/ 56D920871A/ 56D920871/ 56D920861), after 17 years of Beetle

Click “Yes” to start loading external EEPROM data files.

Click “No” to start uploading data to the server.

This instrument requires no reading and loading EEPROM 95320, so here we tap “No” to start the calculation.

This will take about 5-10 minutes to complete the calculation.

www.vvdishop.com