Problem:
Brand new xhorse vvdi key tool max pro just going through the set up. Been stuck on this screen for 20 mins. Any suggestions?
Solution:
Network issue.
Get a faster internet connection or use WiFi hotspot.
Or turn it off, and downloaded again. It works out just fine.
User feedback:
Just had to turn it off and try again. It worked.
Today I’m gonna show how to add a new smart key for 2009 FIAT500 first version with Xhorse VVDI Key Tool Max PRO by OBD.
Turn ignition on.
Connect VVDI Key Tool Max PRO to car OBD port.
Immo programming >> FIAT >> Select by area >> European area >> 500 >> Flip-key(2008-2017) >> IMMO system(DELPHI 93C86_ID46) >> Start programming >> Type 1(93C86) >> Display immo information(PIN, Key ID)
Here we can check the password: 27665
Press “Make dealer key”
Please put the key or blank 46 chip in the sensing coil of the Key Tool Max PRO and keep it still, because some non-original key position will be different.
Press OK.
Generating dealer key, please wait…
Generate dealer key successfully.
Press “Key programming”.
All keys that can start the vehicle must be programmed, keys that are not programmed will be scrapped(cannot be programmed again).
The new key to be programmed must be a dealer key!
Press Yes to continue.
Please enter a 5-digit security code: 27665
Here Key Tool Max PRO will automatically enter it.
Switch ignition on.
Current key number: 2
Insert the wanted programming key, switch ignition on.
Programmed successfully.
Press Yes to program next one.
Remove the current key, then insert the key to be matched and turn on ignition!
Programmed successfully.
Press No to continue.
Turn the ignition off.
Switch ignition on.
Key program function ends.
Current number of keys: 2
Please make sure whether the key function is normal!
Test the new keys, both can start the car and remote work OK.
Done.
2017 Pathfinder, add-key with Autel IM508. It’s not taking any of the keys in, even their original key.
No DTC codes until after a few shots, now flagging B2198.
UPDATED:
My Xhorse VVDI Key Tool Key Max Pro came to the rescue.
It’s saved my ass on several Nissans that my Autel wouldn’t do.
Popped right in with it, after running the programming process on my Key tool max pro a second time. First time, the remotes took, but not the chips. Second programming run with the Key tool max pro, the chip programmed in. Not the first time my 508 failed me, either. The code went away after programming with the Xhorse tool.
www.vvdishop.com
It is a Toyota Land Cruiser Prado 150 2013 with keyless entry system. Here we will show how to add a spare key to this module using xhorse vvdi key tool max pro and XM38 smart key.
First, read the information of the chip and radio channel from the original remote control.
At the top are the Xhorse keys, and below are the original ones. Xhorse keys are very nicer than their relatives.
We read the data on the chip and radio channel from the original keys, click generate remote control.
Preparing/generating a new key/remote.
Programming the immobilizer, selecting the brand, model and immo system.
Turn on ignition switch and confirm.
Select Add Key.
We see the number of keys registered in the system is 2 and the maximum number is 5.
Put the original key close to the engine Start button within 30s, you should hear a beep.
Put the Xhorse XM38 Toyota smart key to the ignition switch.
Here we see that the number of registered keys has become 3, and the number of which can be additionally registered has decreased by one.
It says that if the remote control does not work, you need to perform a synchronization procedure.
The key was added without any problems.
How-to: add Renault Kadjar 2019 smart key with xhorse vvdi key tool max pro and Xhorse King card.
Select IMMO Programming->Renault->4A chip smart key->IMMO Programming
Step 1: Make dealer key
Turn on emergency indicators
Turn off emergency indicators, wait 5 minutes and turn on again
Online calculation
Put the key in the sensing coil of the key tool max pro
Read Key ID
Generate dealer key successfully
Step 2: Program key
You need to program all the keys.
Turn iff emergency indicators.
Put 1st key to be programmed close to start button, take other keys more than 1 meter outside the car.
Turn on emergency indicators.
Program 1st key successfully.
Repeat and program 2nd key
Put xhorse king card close to start button
Program king card successfully
Programming completed.
Test all keys.
Done.