Read VW RCD510 Radio NEC and EEPROM by Xhorse VVDI Prog

 How to read Nec V850 D70F3356 Processor & 95128 Eeprom with xhorse vvdi prog to get VOLKSWAGEN 5k0035190a Bosch RCD510 Entry Radio Code.

Step 1:

Read Nec V850 D70F3356

Connect Nec V850 D70F3356 processor with vvdi prog via mcu3 adapter

In vvdi prog software, select MCU-Renesas V850- D70F3356 and save data

Step 2:

Read eeprom

Connect 95128 mcu with vvdi prog via clip adapter.

With clip adapter you don’t need to unsolder the chip from the board.

Select EEPROM-ST-M95128

Read and save eeprom data

Code location in eeprom – line 000AE0 ( 8А 37 8D A4 ). Code = A7D4 x or XXXX. To calculate XXXX – need a dump NEC.

Open dump,  try the 0xAE0 to 0xD00 fill to 0xFF method, and get the data after “Power on”.

There are also 3rd party radio code calculators available.

www.vvdishop.com

How to Clone Benz C220 W204 SAM Module with VVDI Prog

How to clone Mercedes C220 W204 front SAM module using xhorse vvdi prog?

Mercedes W204 front SAM module pinout to vvdi rpog

Follow wiring diagram to connect SAM module with vvdiprog

Read SAM module data

Select 8-Other->Benz->W204 Front SAM Module

Save data.

Connect a new front SAM module with vvdi prog programmer

Write data to new SAM module

www.vvdishop.com

How to Fix VVDI Prog JLR BCM XEP768 Partition information error

 Problem:

I try to clone a JLR BCM XEP768 (2009-)with xhorse vvdi prog, i get a message. Partition information error.
What is the correct way, to get the full data, needed to clone these.

Solution:

Use this

Set D-Flash partition to 128 sectors (32K)
Set EEPROM partition to 0K

Pinout LANDROVER BCM 2009 MC9S12XEP768

LANDROVER BCM 2009

Citroen C4 ABS 2L09S Pinout to Xhorse VVDI Prog

 Here comes the Citroen C4 ABS MC9S12C128 mask 2L09S Pinout to Xhorse VVDI Prog programmer.

C4 module ABS MC9S12C128 unsecured pinout VVDIProg

Credit to DK Veteran.

Read ID OK

Read data ok

Download 2L09S read all.bin

UPA USB  pinout

Download upa modify.bin

How to Reset BMW F20 FEM Mileage with VVDI BIMTool Pro

 Tutorial: BMW Series F series Reset FEM BDC mileage eeprom 95128-95256 using Xhorse VVDI BIMTool Pro.

i.e. F20 FEM module

Procedure:
Remove BMW FEM module from the vehicle

Set up bench connection. Connect VVDI BIMTool pro with godiag BMW FEM test platform, FEM module, feed vvdi with 12v+ power supply (very important)

Turn on ignition switch of the godiag test platform

Run Xhorse vvdi bim tool software, go to BMW/FEN Key Learn and Get key Information
As you can see 2 keys are programmed and you can see VIN and current mileage is 183374 KM

Press Reset KM
BIMTool will ask to program FEM/BDC first

Press Program BMW FEM/BDC System

Follow 4 steps to program BMW FEM/BDC

Step 1. Backup coding
Read FEM/BDC coding ia OBDII or on bench
Step 2. Prepare service EEPROM
Open FEM/BDC shell, find 95128/95256 chip position, read EEPROM dump via BDM programmer
Load original eeprom dump and save special EEPROM dump, write special EEPROM dump back to 95128/95256 chip
Restore FEM/BDC shell, provide 12v+ and connect OBD

Step 3. Programming
This operation require connect FEM/BDC on bench and make sure you finish step 1 and step 2
provide 12v+ and connect OBD

Step 4. Restore original eeprom
Open FEM/BDC shell, write original EEPROM Dump read in step 2 back to 95128/95256 chip
Restore FEM/BDC shell, provide 12v+ and connect OBD

Step 5. Restore coding
Load coding file read in step 1, write to FEM/BDC via OBDII, finish FEM/BDC programming

Follow instructions to operate step by step.

First of all backup coding

Step 2

Open FEM/BDC shell, find 95128/95256 chip position, read EEPROM dump

You can solder the chip and read with programmers (VVDI Prog, Orange5, Carprog original etc) with eeprom adapter
Or read with vvdi prog and FEM clip adapter without soldering

(Remove and solder chip method is recommended as some say the clip adapter has a risk to lost data)

Read 95128 or 95256 eeprom data with vvdi prog and save original eeprom data

Load the original eeprom dump file read above

Next step is to write service eeprom dump file

Then FEM/BDC programming is processing

Open FEM/BDC shell, write original EEPROM Dump read in step 2 back to 95128/95256 chip

Load original coding file and write to FEM/BDC module

Writing coding.

NOTE:

If failed to write coding on bench, reconnect the power for BMW FEM BDC system, load the coding file again.

VVDI BIM TOOL Pro BMW FEM/DC programming success.

Get key information again, the mileage is 0 KM now.

Restore BMW FEM/BDC module back to vehicle and driver a test.

Done.

http://blog.vvdishop.com/reset-bmw-fem-km-with-vvdi-bimtool-pro/