ابزار Xhorse VVDI

Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزار

ابزار Xhorse VVDI

Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزار

How to Calculate Audi MQB48 IMMO Data by VVDI MLB Tool MQB48 Adapter

 Here we will show how to calculate VAG MQB48 NEC35XX immo data with Xhorse VVDI MLB Tool and MQB48 adapter.

 

Model example: Audi Q2.

Tools used:

VVDI MLB Tool

MQB48 adapter

Original key

A new key to be programmed

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 1

Before using MQB48 adapter, we should modify MLB tool firmware as following:

How to Update VVDI MLB Tool Firmware to Use MQB48 Adapter?

Then we start to read immo data with MLB tool.

Run VVDI MLB Tool software. Choose MQB48 function and check wiring diagram.

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 2

Select corresponding wiring diagram. Here the key board is the same as type 5.

Need to solder 2 wires, black wire and red wire.
Remove a capacitor, the solder the red wire (near the IC position).

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 3

Open the original key shell.

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 4

Remove a capacitor as shown in the wiring. Then solder two wires.

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 5

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 6

Connect Xhorse XDMQBAGL MQB48 Adapter with MLB Tool.

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 7

Connect Key board with MQB48 adapter. Place the key to coil of MQB48 adapter in the vertical direction.

The MQB48 adapter has strict power supply requirements during data collection. Use two separate USB cables to power the MLB main unit and the MQB48 collector. Do not use charging adapters.
The MLB main unit does not require 12V power.

Then connect MLB Tool with PC via USB cable.

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 8

Read key information. Read Key ID successfully.

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 9

Press Collect Key data.

Collecting key data and calculating immo data.

Calculation finished. Restore key back to original status. Save MQB NEC35XX immo data.

Data Collection Time:
Good power supply: ~15 minutes for data collection, ~1 minute for immobilizer data calculation.
Average power supply: ~30–60 minutes for data collection, ~1 minute for calculation.

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 10

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 11

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 12

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 13

Resolder the capacitor back to the key. Reinstall key shell. This is very important !!!

 

NOTE:

Removing the wrong capacitor can cause the MQB chip to become unrecognizable, making it impossible to collect data.
After reading the data, the capacitor must be restored; otherwise, the key cannot be programmed to car.

 

If need to connect MLB tool with key tool plus to calculate MQB48 immo date, make connection like this:

Note: Tablets with a single Type-C port have poor power stability, leading to longer collection times and lower success rates. Strongly recommend using a PC.


Connect VVDI2 or VVDI Key Tool Plus with vehicle via OBD connector.
Go to MQB anti-system system (NEC35XX Continental/VDO), read cluster info.
Load immo data saved by MLB Tool.
Then generate dealer key and learn key.

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 14

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 15

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 16

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 17

Read MQB48 IMMO Data with VVDI MLB Tool and MQB48 Adapter 18


www.vvdishop.com

نظرات 0 + ارسال نظر
امکان ثبت نظر جدید برای این مطلب وجود ندارد.