ابزار Xhorse VVDI

Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزار

ابزار Xhorse VVDI

Xhose VVDI نرم افزار برنامه نویس اصلی و سخت افزار

VVDI2 VAG Program Audi Q7 2007 Remote key by OBD

Here vvdishop introduces 2 ways to program remote smart key on a Audi Q7 year 2007 with Xhorse VVDI2 key programmer by OBD.

audi-q7-2007-obd-location

Connect Xhorse VVDI2 VAG key programmer with vehicle through OBD connector

Audi Q7 OBD diagnostic connector location

vvdi2-audi-q7-2007-1

The remotes to be programmed use ID8E transponder

vvdi2-audi-q7-2007-2

vvdi2-audi-q7-2007-3

vvdi2-audi-q7-2007-4

First, we show how one of the two remotes is deprogrammed

Original key can turn on the switch, remote key to be programmed cannot.

 

 

Method 1:

Open VVDI2 software

vvdi2-audi-q7-2007-5

vvdi2-audi-q7-2007-6

Select Audi->Key Learn-> 4th Immobilizer system-Audi-> A6L/Q7/Allroad

Turn ignition ON

We extract the necessary information (Pin Code and Security Code) of the vehicle to access and be able to perform the final process of programming (Key Learn)

vvdi2-audi-q7-2007-7

Select Autodetect from engine (ECU)

Reading data, please wait

Reading data success

We observe on the above screen the information of security codes (Pin Code and Security Cop) extracted correctly

 

Let’s go to the final programming process (Key Learning)

vvdi2-audi-q7-2007-8

Enter number of keys to learn: 2

and press Key Learning button

vvdi2-audi-q7-2007-9

Insert the dealer key into car and switch on for at least 2 seconds. The time for change key should  within 5 seconds. Press OKAY button after all key is learned.

vvdi2-audi-q7-2007-10

All keys successfully learned.

 

 

Method 2:

Next, we will see another method of programming.
In this case, more direct and automatic.
And with information on the status of immobilizer and possible vehicle lock by incorrect Pin Code or transponder to
real-time on-screen.

In VVDI2 Audi Menu

vvdi2-audi-q7-2007-11

Select Key Learn->Key Learn

vvdi2-audi-q7-2007-12

Auto detect vehicle: A6L/Q7/Allroad 2005+, CAN

Select Autodetect PIN/CS

Automatic detection / extraction of the security codes (Pin Code and Comp. Of Security)

vvdi2-audi-q7-2007-14

Real-time status information of the Immobilizer: type of key / transponder and its status, access to units, number of keys programmed

vvdi2-audi-q7-2007-15

Real-time information on possible vehicle lockout and remaining time for leaving it

vvdi2-audi-q7-2007-13

PIN and CS Security codes successfully extracted

Enter key number in marked red area: 2

Press Learn button

Insert entry key and switch on ignition

We accept OK to finish the process once the steps are done correctly

Test the new programmed remote key.

http://blog.vvdishop.com/xhorse-vvdi2-program-audi-q7-2007-remote-key-by-obd/

VVDI2 and Tango key programmer which is better

Topic: VVDI2 or Tango? Which is better for auto key programming?

 

Program keys: VVDI2 via OBD, Tango from dump

 

If you are going to make keys from dump and reading with a programmer buy Tango.
If you are looking to make keys over OBD buy VVDI2 is a good tool for BMW CAS/MB EZS. (read and write MB IR key)
Tango more features, VVDI2 good for OBD

Better buy VVDI2 with VVDI Prog

I personally prefer Tango good support and more features, xhorse it is also a very good for obd.
If you buy VVDI2 i also recommend complement with VVDI programmer.

 

Tango has guides with pics, free with standard tool

 

I don’t know VVDI2… but I have tango and it’s excellent so long as you have good programmers too like xprog etc. Most makes/models have guides with pics. Also many makers are free with standard tool and you can just add when you need

 

VVDI2 + Tango better than Zed full

 

If you mean original Tango and VVDI2 full…than this group will be better than zed full, thats my opinion…but there is a lot of car that you will need to remove BCM’s, immo’s…etc because vvdi2 and tango are more eeprom based tools, except vvdi2 making bmw and vag over obd2, skp900 and obdstar are obd2 tools but cant help you with fiat, opel, renault and with some few brands

 

VVDI2 + VVDI Prog good for VAG + BMW

 

If you looking only for VAG + BMW , then VVDI2 and VVDI prog is way to go. No need any other tool. In VVDI2 you have also programmer similar to Tango that you can make keys buy dump, but 90% of VAG and BMW can be done by OBD in VVDI2.

 

VVDI2 = VVDI + Tango + …

 

VVDI 2 includes all the VVDI functions, the function of Tango…. has improved remote control generation and chip identification, and also enhanced the coil’s stability
Moreover, you don’t have to connect VVD2 with a computer or other devices to identify chip or detect remote frequently.

 

 

Conclusion:

VVDI2 wins! Wins in OBD making keys! Wins in VAG + BMW key programming.

 

VVDI2 BMW:

Correct odometer
Generate key
Unlock key
Fix CAS computer

 

VVDI2 VAG:

Read & write Immo4/Immo5 system
Learn key
Program BCM remote
K-Line instrument immobilizer box
Correct odometer
Program control unit
Unlock Immo1/Immo2 firmware protection
Support data manipulation tools

 

VVDI2 key programmer:

Program key chip
Generate specialized chips
Immobilizer data processing tool
Other key tools
Generate remote control

www.vvdishop.com

Solved) VVDI2 Program key on VW Transporter UDS System

If you have Xhorse VVDI2 VAG key programmer to add dealer key on VW Transporter/Caravelle T5 2011, but not work, you must read this post, the problem is finally solved.

 

Problem description:

VW Transporter/Caravelle T5 2011. Had an existing working key and used Xhorse VVDI2 to make a dealer key on a UDS cluster but something went wrong or more likely I did something wrong. It says 2-2 on the cluster and lights go off as if programmed but once cranked it starts and dies and the glow plug indicator light flashes. I stripped the cluster and tried with putting the cluster in to service mode but still much the same. With AD100 it says 2 keys coded and cluster in Mode 7. A friend came with his Zedfull and recoded in both keys and it said precoding ok but still the same issue. The dump of the original 24c64 and the backup I first made are attached and I’d appreciate any advice or help on this. Thanks everyone

 

folder: Transporter T5 24c64 Original Read

Folder: Transporter T5

UDS Dash Info

Advice:

Config: This value contain car manufacture, key number, immobilizer status (new, learned, closed), keyless or not etc.

 

Your immo status is likely changed, did you press the reset immo button.

When did you made the 24c64 backups.

After entering service mode true obd, or after your keylearning procedure?

 

Question:

The initial backup (small file)was made before I made the key but I read the 24c64 only after it wouldn’t start. Any idea how to change the config from o7 to 06 again?

 

Instruction guide by senior:

go in to service mode by obd.

read immo data.

change the conf 7 in to 6.

press, write immo data.

press, reset instrument.

that should do it.

 

Finally! Solved

Thanks everyone. Yes it was me being stupid, I think I actually wrote the 24c64 complete file back instead of the smaller immo file. Did as advised and problem solved.

 

www.vvdishop.com

http://blog.vvdishop.com/solved-vvdi2-make-a-dealer-key-on-vw-transporter/

VVDI2 Reading Audi A6 / Q7 EEPROM from EZS

Here is the instruction showing the capabilities of the Xhorse VVDI2 VAG key programmer: Reading EEPROM with EZS Audi A6 / Q7

 

How to read eeprom from EZS AUDI by OBD with VVDI2:
Select Key Learn->4th immobilizer system- Audi-> A6L/Q7/Allroad

vvdi2-read-audi-a6-ezs-eeprom-1
A6L/Q7/Allroad EZS-Kessy (J518) 4th immobilizer system

Select Auodetect from engine (ECU)

vvdi2-read-audi-a6-ezs-eeprom-2
reading data, please wait

Reading data success

vvdi2-read-audi-a6-ezs-eeprom-3

Read and save EZS-Kessy EEPROM (J518)
Start security login
Reading data…

Reading data success
Save eeprom

vvdi2-read-audi-a6-ezs-eeprom-4
click on Read VIN

vvdi2-read-audi-a6-ezs-eeprom-5

VVDI2 Read Audi VIN successfully.

www.vvdishop.com

How to use VVDI2 to add key for Passat 2013 NEC Dash

Here is the guide to use Xhorse VVDI2 VAG key programmer to add key for Passat 2013 with VDO NEC+24C64 dashboard by OBD.

 

VVDI2 adds Passat 2013 Key Guide:

Go to VVDI2 software-> select VW car brand

vvdi2-passat-2013-key-1

vvdi2-passat-2013-key-2

Select Key Learn->4th Immobilizer system-VW/Skoda/Seat->Auto detect type
VVDI2 read VIN ECU and dash type: NEC+24C64

Click on Diagnosis

Click on Read EEPROM/FLASH
Select Read eeprom, click on Next

vvdi2-passat-2013-key-3
Turn ignition to ON position (If it is smart key, turn ignition OFF then turn it ON)

Dash instrument screen is in black, it is normal

vvdi2-passat-2013-key-4

Follow VVDI2 key programmer prompts:

1.Dashboard is in black, complete following steps to activate the dash:

2.Read and save eeprom data

3.Read and save IMMO data

4.Generate a dealer key (if has working key and does not need to add a key, skip to Step 7)

5. Reset dash

6.Key learning from immo data

7. Other functions

vvdi2-passat-2013-key-5
Reading eeprom data
Dave eeprom data

vvdi2-passat-2013-key-6
Read Immobilizer data
Save immo data

Click on Generate Dealer Key

vvdi2-passat-2013-key-7

Choose car manufacture->VW

Select Prepare normal dealer key

vvdi2-passat-2013-key-8
Insert car key into vvdi2 VW

vvdi2-passat-2013-key-9

click Next
confirm YES to generate VW normal dealer key

Generate dealer key success

vvdi2-passat-2013-key-10

all preclude done

vvdi2-passat-2013-key-11

Reset dash

vvdi2-passat-2013-key-12

Reset success. Dash activated.

vvdi2-passat-2013-key-13

Select Add key

(Make sure you have backup both eeprom and immo data)

vvdi2-passat-2013-key-14

Select 2nd option to do key learning and enter key numbers to to learned
click on Next

Turn ignition to ON position (If it is smart key, turn ignition OFF then turn it ON)
Confirm if it is smart key

vvdi2-passat-2013-key-15

If the dash display 1-2, insert next key into VVDI2’s coil

vvdi2-passat-2013-key-16

Insert second key within 5 seconds, turn ignition ON for 2 seconds, dash displays 2-2

Key Learning success

vvdi2-passat-2013-key-17

Start engine with the new key.

Done!

www.vvdishop.com

http://blog.vvdishop.com/vvdi2-vag-add-key-for-passat-2013-by-obd/