VVDI MB Program Benz E350 2005 W211 BE Key

How to: Program the Mercedes-Benz 350 E-CLASS 2005 model W211 key easily using Xhorse VVDI PROG and VVDI MB Tool key programmer.

Step 1: Read EIS data with VVDI Prog

Connect EIS with vvdi prog followed by wiring diagram

Benz EIS W203 W211 HC12 wiring connection to vvdiprog

Open vvdi-prog software, read data

Save eeprom data.

Step 2: Program new key with VVDI MB

Open VVDI MB software

Select EIS Tools->Load EIS data

VVDI MB tool displays current key information, save EIS data

Save new EIS data to HC05 format

Go to Prepare Key File->Load EIS file

load new EIS data

Untick V41 and press Prepare Key file

Preparing key progress until completed.

Go to Read/Write Key, check BE key that unuse

Load Key file->Choose key number 3->Write 

Write key success. Now this key ready to start.

Done.

http://www.vvdishop.com

http://www.vvdishop.com/service/program-benz-e350-2005-w211-be-key-with-vvdi-prog-vvdi-mb-8075.html

Program Benz Sprinter Key with VVDI Prog and VVDI MB

How to: Program key for Benz Sprinter W906 using Xhorse VVDI prog and VVDI MB Tool key programmer.

Step 1: Read EZS data with VVDI Prog

Open VVDI-Prog software

Select 4-Immobilizer->Benz->EIS W906 (ST12)

Check connection wiring

Follow Benz EIZ W906 ST12 0L01Y wiring diagram to connect EIS with vvdi prog

Read eis data

Save data

Step 2: Program key with VVDI MB

Open VVDI MB software

Select Prepare Key File->Load EIS file

Upload EIS data read by vvdiprog

Display key information, select key version v51, then press Prepare Key File

Save new key data

Go to Read and Write Key->Identification key

Press Load key file to upload new key data

Press Write button to write key

Program Sprinter key success

Done.

www.vvdishop.com

http://blog.vvdishop.com/vvdi-prog-and-vvdi-mb-program-key-benz-sprinter-w906/

VVDI Adds Land Rover Discovery 3 2007 Transponder Key

New test report:  I’ve successfully added a PCF7936 transponder key to a Land Rover Discovery 3 BCM using Xhorse VVDI Prog and VVDI2 programmer.

Step 1: Read CEM Dump with VVDI Prog

Open VVDIprog software, select Type: 4 Immobilizer->Land Rover->Discovery3-CEM

Press Connection Diagram

PGD need connect a 10k resistor to VCC

Connect VVDI Prog with BCM module following the wiring diagram

You need also modify MCU reflash cable from V2 to V3 following the picture operation guide below

Then back to vvdi software

Read and then save BCM eeprom dump data, i.e: LANDROVER.bin

Step 2: Make dealer key with VVDI2

Open VVDI2 software->Immobilizer Data Tool

Select Area: Europe->Land rover-> Discovery 3

Load EEPROM dump (LANDROVER.bin) read by vvdiprog

VVDI2 detects key information, 2 keys have been programmed. Select valid key position Key3 and press Make Dealer Key

Insert a PCF7936 chip into VVDI2’s detection coil

Prepare dealer key success. It start engine after write back new dump file or learn it to car.

Save new dump key file,i.e LANDROVER OKK.bin

Load new key dump file, you’ll see Key 3 was programmed successfully

Step 3: Write new key dump back to BCM with VVDI-Prog

Go back to vvdi prog software

Open new key dump LANDROVER OKK.bin

Press Write button

Operation success.

Reinstall BCM unit back to vehicle

Test the new transponder key.

Done.

http://www.vvdishop.com

http://www.vvdishop.com/service/vvdi-prog-and-vvdi2-adds-land-rover-discovery-3-2007-bcm-key-8074.html

PSA IAW 6LP pinout to Xhorse VVDI-Prog

PSA IAW 6LP pinout to VVDI Prog: IAW 6LP2.01/2.05 and IAW 6LPC105

IAW 6LP2.01 pinout VVDi Prog

IAW 6LP2.05 pinout VVDiProg

IAW 6LPC.105 Pinout VVDi-Prog

VVDI Prog read BSI Marelli MC68HC912DG128

Here’s the Xhorse VVDI Prog programmer pinout to bsi magnet marelli.

I have successfully read bsi magnet marelli whit vvdi prog,mcu is MC68HC912DG128 unsecured

Mask:5H55W , using this wiring diagram , hope this will be useful for somebody used

wires are VCC -red

GND black ,

reset- yellow

and BKGD – purple

Credit to iozo from DK forum.

http://www.vvdishop.com

http://blog.vvdishop.com/read-bsi-magnet-marelli-mc68hc912dg128-with-vvdi-prog/